Honda Odyssey 2004. Manual — part 375
01
02
S0X4A00J18573430201KBAT00
20-142
Exterior Trim
Front Grille Replacement
Fastener Locations
: Clip, 11
A
Fastener Locations
: Clip, 3
A
NOTE:
• When prying with a flat-tip screwdriver, wrap it with
protective tape to prevent damage.
• Take care not to scratch the front bulkhead cover and
front grille.
1. Detach the clips, then remove the front bulkhead
cover (A).
2. Detach the clips, then remove the front grille (A).
3. Install the front grille in the reverse order of
removal, and note these items:
• Replace any damaged clips.
• Push the clips into place securely.
03/07/29 10:03:39 61S0X050_200_0144
01
S0X4A00J18573430201MFAT00
20-143
Front Grille Disassembly/Reassembly
Fastener Locations
: Screw, 18
FRONT GRILLE
EMBLEM
MOLDING
SPEED NUTS
NOTE: Take care not to scratch the front grille and molding.
Replace.
03/07/29 10:03:39 61S0X050_200_0145
*01
*02
S0X4A00J18573424101KBAT00
’02-04 models
20-144
Exterior Trim
Emblem Replacement
Unit: mm (in.)
’99-01 models
’’H’’ EMBLEM
ODYSSEY EMBLEM
28
(1.1)
28
(1.1)
114
(4.5)
ODYSSEY EMBLEM
Edge of the tailgate
Center
Edge of the tailgate
26 (1.02)
’’H’’ EMBLEM
Center
’’H’’ EMBLEM
Edge of the tailgate
15 (0.59)
NOTE: When removing the emblems, take care not to
scratch the tailgate. Use dental floss to cut the adhesive
safely.
Apply the emblems where shown, and note these
items:
• Clean the tailgate surface with a sponge dampened in
alcohol.
• After cleaning, keep oil, grease and water from
getting on the surface.
03/07/29 10:03:40 61S0X050_200_0146
*01
S0X4A00J18573451651KBAT00
20-145
Roof Rail Replacement
Fastener Locations
: Bolt, 2
: Nut, 1
E
F
: Nut, 5
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
6 x 1.0 mm
13 N·m
(1.3 kgf·m,
9.4 lbf·ft)
B
C
D
D
A
C
F
F
G
I
F
F
H
J
K
F
E
NOTE:
• When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.
• Take care not to scratch the covers, roof rail and body.
1. Remove the front cover (A) and rear cover (B) by sliding them in the direction shown while pushing the spring
plate (C) through the hole on each bracket with a flat-tip screwdriver. Remove the center cap (D), then with a Torx
T30 bit, remove the nuts (F) from the front bracket (G) and rear bracket (H).
2. Remove the roof rail (I). Do not remove the rubber pads from the brackets.
3. Remove the center cover (J). Using a Torx T30 bit, remove the nuts (E, F) and the center bracket (K). Do not
remove the rubber pad from the center bracket.
4. Install the roof rail in the reverse order of removal. Make sure the front and rear covers are snapped tightly into
place.
03/07/29 10:03:40 61S0X050_200_0147
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст