Honda Odyssey 2004. Manual — part 290
15
*01
02
S0X4A00F00000059501KBAT00
Special Tools Required
17-48
17-48
Power Steering
Steering Gearbox Installation
(cont’d)
Tie-rod Ball Joint Boot Replacement
A
B
C
E
A
C
B
D
D
A
B
07965-SA50500
25. Install the steering joint cover (A) with the clamps
(B) and clips (C).
26. Fill the system with power steering fluid, and bleed
air from the system (see page 17-14).
27. After installation, perform the following:
• Start the engine, allow it to idle, and turn the
steering wheel from lock-to-lock several times to
warm up the fluid. Check the gearbox for leaks
(see page 17-11).
• Adjust the front toe (see step 1 on page 18-7).
• Check the steering wheel spoke angle. Adjust by
turning the right and left tie-rods equally, if
necessary.
• Do the PCM idle learn procedure (see page 11-
202).
• Do the power window control unit reset
procedure (see page 22-200).
• Set the clock.
• Enter the anti-theft codes for the radio and the
navigation system, the custmer’s radio station
presets.
Front hub dis/assembly tool 07965-SA50500
1. Remove the boot from the tie-rod end, and wipe the
old grease off the ball pin.
2. Pack the lower area of the ball pin (A) with
multipurpose grease.
3. Pack the interior of the new boot (B) and lip (C) with
multipurpose grease.
Note these items when installing new grease:
• Keep grease off the boot installation section (D)
and the tapered section (E) if the ball pin.
• Do not allow dust, dirt, or other foreign materials
to enter the boot.
4. Install the new boot (A) using the special tool. The
boot must not have a gap at the boot installation
sections (B). After installing the boot, check the ball
pin tapered section for grease contamination, and
wipe it if necessary.
03/07/29 09:49:45 61S0X050_170_0048
S0X4A000000000J1801ZCAT00
Suspension
Front and Rear Suspension
Front Suspension
Rear Suspension
. . . . . . . . . . . . . . . .
. . . . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . ...
. . . . . . . . . . ...
. . . . . . . . . . . . . ..
. . . . . . . . . . . . . . . .
. . . . . . . . . .
. . . . . . . . . . . . . . .
. . . . . . ...
. . . . . . . . . . ...
. . . . . . . . . . . . . ..
Special Tools
. 18-2
Component Location Index
. 18-3
Wheel Alignment
. 18-5
Wheel Bearing End Play Inspection
. 18-8
Wheel Runout Inspection
. 18-9
Ball Joint Removal
. 18-10
. . . . . . . . . . .
. . . . . . . . . ..
. . . . . . . ...
. . . . . . . . . .
. . . . . . . . . . .
. . . . . . . . . ..
. . . . . . . ...
. . . . . . . . . .
Knuckle/Hub Replacement
. 18-11
Ball Joint Boot Replacement
. 18-16
Lower Arm Removal/Installation
. 18-17
Damper/Spring Replacement
. 18-18
. . . . . . . . . . ..
. . . . . . . ...
. . . . . . .
. . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . ...
. . . . . . . . . . ..
. . . . . . . ...
. . . . . . .
. . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . ...
Hub/Bearing Replacement
. 18-22
Upper Arm Removal/Installation
. 18-26
Lower Arm A Removal/Installation
. 18-27
Lower Arm B Removal and Installation
. 18-28
Trailing Arm Removal/Installation
. 18-29
Damper Removal and Installation
. 18-30
Spring/Bump Stop Replacement
. 18-32
03/07/29 09:50:54 61S0X050_180_0001
01
01
01
01
01
01
01
01
S0X4A000000000J1801PAAT00
Ref. No.
Tool Number
Description
Qty
18-2
Front and Rear Suspension
Special Tools
07AAF-SDAA100
Ball Joint Thread Protector, 12 mm
1
07GAF-SE00100
Hub Dis/Assembly Tool
1
07MAC-SL00200
Ball Joint Remover, 28 mm
1
07746-0010500
Attachment, 62 x 68 mm
1
07749-0010000
Driver
1
07948-SB00101
Attachment, 96 mm
1
07965-SD90100
Support Base
1
07974-SA50700
Ball Joint Boot Clip Guide
1
03/07/29 09:50:56 61S0X050_180_0002
*01
S0X4A00B20200000000DAAT00
18-3
Component Location Index
FRONT DAMPER
LOWER ARM
HUB
KNUCKLE/
Removal, page 18-19
Disassembly/Inspection, page 18-19
Reassembly, page 18-20
Installation, page 18-20
Removal/Installation, page 18-17
Replacement, page 18-11
03/07/29 09:50:57 61S0X050_180_0003
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст