Honda Odyssey 2004. Manual — part 348
01
02
S0X4A00J34300044001KBAT00
20-34
Mirrors
Manual Mirror Replacement
Fastener Location
: Clip, 1
A
Fastener Locations
: Bolt, 4
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
B
1. Lower the door glass fully.
2. Carefully pry out the mirror mount cover (A) by
hand as shown.
3. Remove the bolts securing the mirror. While
holding the mirror (A), push out the clip (B), and
remove the mirror. Take care not to scratch the
door.
4. Install the manual mirror in the reverse order of
removal, and push the cover clip into place
securely.
03/07/29 10:00:21 61S0X050_200_0036
01
02
S0X4A00J34300044021KBAT00
20-35
Mirror Holder Replacement
A
B
C
E
D
A
A
C
D
C
E
E
A
1. Push in the bottom of the mirror holder (A).
2. Insert a flat-tip screwdriver wrapped with a shop
towel at the bottom gap between the mirror holder
and mirror (B). Push the mirror holder upward to
release the hooks (C, D) from the actuator adapter
plate (E) while holding the mirror holder.
3. If equipped, disconnect the mirror defogger
terminals (A).
4. Install the mirror holder in the reverse of the
removal, and note these items:
• If equipped, make sure the terminals are plugged
in properly.
• Push the mirror holder downward to lock in the
hooks.
• Push in the bottom of the mirror fully before you
push on the mirror holder.
• Check the operation of the actuator.
03/07/29 10:00:21 61S0X050_200_0037
*01
*02
S0X4A00J34300034651KBAT00
20-36
Mirrors
Rearview Mirror Replacement
A
C
B
A
1. Turn the rearview mirror base (A) 90°.
2. Slide the rearview mirror (A) down toward the
bottom of the windshield to detach it from the
spring (B) in the mount (C).
3. If necessary, remove the spring from the mount.
4. Install the rearview mirror in the reverse order of
removal.
03/07/29 10:00:22 61S0X050_200_0038
*01
S0X4A00J54400000000DAAT20
20-37
Glass
Component Location Index - Windshield-Rear Window
MOLDING CORNER
SEAL, 2
(’00-04 models)
MOLDING UPPER SEAL, 2
(’99-00 models)
WINDSHIELD
REAR WINDOW
UPPER CORNER FASTENER, 2
(Self-adhesive-type, body side)
(Required for replacement
or reinstallation)
UPPER CORNER FASTENER, 2
(Self-adhesive-type, glass side)
(Required for replacement
or reinstallation)
LOWER CORNER FASTENER, 2
(Self-adhesive-type, glass side)
(Required for replacement or reinstallation)
LOWER CORNER FASTENER, 2
(Self-adhesive-type, body side)
(Required for replacement or reinstallation)
SEAL
RUBBER DAM
SIDE RUBBER DAM
(Required for replacement
or reinstallation)
UPPER RUBBER DAM, 2
(Required for replacement
or reinstallation)
LOWER RUBBER DAM
MOLDING SIDE SEAL, 2
(’99-00 models)
DASHBOARD SEAL
UPPER RUBBER DAM
FASTENER, 2
(Self-adhesive-type, body side)
(Required for replacement or reinstallation)
FASTENER, 2
(Self-adhesive-type, glass side)
(Required for replacement or reinstallation)
UPPER SPACER
SIDE SPACER, 4
WINDSHIELD
MOLDING
Replacement, page 20-39
Replacement, page 20-45
03/07/29 10:00:22 61S0X050_200_0039
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст