Honda Odyssey 2004. Manual — part 188
*01
01
S0X4AA0E10410422251KDAT00
14-146
14-146
Automatic Transmission
Transmission Removal (cont’d)
Drive Plate Removal and
Installation
12 x 1.25 mm
74 N·m (7.5 kgf·m, 54 lbf·ft)
B
A
55. Lower the transmission, and tilt the engine just
enough for the transmission to clear its end cover
from the side frame.
56. Place a transmission jack under the transmission.
57. Pull the transmission away from the engine until it
clears the dowel pins, then lower it on the
transmission jack.
NOTE: If the torque converter is stuck to the drive
plate, pull it toward the transmission housing from
the starter opening.
58. Remove the shift cable cover, then remove the
torque converter assembly from the torque
converter housing.
59. Inspect the drive plate, and replace it if it’s
damaged.
60. Remove the 6 x 1.0 x 14 mm bolt that you installed
on the shift cable cover in step 31.
1. Remove the drive plate (A) and washer (B) from the
engine crankshaft
2. Install the drive plate and washer on the engine
crankshaft, and tighten the eight bolts in a
crisscross pattern.
03/07/29 09:32:50 61S0X050_140_0149
01
*03
03
04
S0X4AA0E10410400000KCAT00
14-147
Transmission Installation
10 x 1.25 mm
38 N·m (3.9 kgf·m,
28 lbf·ft)
A
A
10 x 1.25 mm
38 N·m (3.9 kgf·m,
28 lbf·ft)
B
A
D
C
E
F
12 x 1.25 mm
64 N·m,
(6.5 kgf·m,
47 lbf·ft)
10 x 1.25 mm
38 N·m
(3.9 kgf·m, 28 lbf·ft)
1. Flush the ATF cooler (see page 14-155).
2. Install the transmission lower mounts (A).
3. Install the torque converter assembly (A) on the
mainshaft (B) with a new O-ring (C).
4. Install the 14 mm dowel pin (D) and 10 mm dowel
pin (E) in the torque converter housing (F).
5. Place the transmission on a jack, and raise it to
engine level.
6. Attach the transmission to the engine, then install
the transmission housing mounting bolts.
7. Install the front mount bracket.
(cont’d)
03/07/29 09:32:51 61S0X050_140_0150
05
07
14-148
Automatic Transmission
Transmission Installation (cont’d)
C
6 x 1.0 mm
12 N·m (1.2 kgf·m,
8.7 lbf·ft)
A
10 x 1.25 mm
38 N·m (3.9 kgf·m, 28 lbf·ft)
D
6 x 1.0 mm
12 N·m (1.2 kgf·m,
8.7 lbf·ft)
B
10 x 1.25 mm
39 N·m (4.0 kgf·m, 29 lbf·ft)
B
A
8. Install the engine stiffener mounting bolts (A).
9. Attach the torque converter to the drive plate (B)
with eight bolts (C). Rotate the crankshaft pulley as
necessary to tighten the bolts to 1/2 of the specified
torque, then to the final torque, in a crisscross
pattern. After tightening the last bolt, check that the
crankshaft rotates freely.
10. Install the torque converter cover (D).
11. Tighten the crankshaft pulley bolt as necessary (see
page 6-18).
12. Install new set ring (A) on the intermediate shaft (B).
13. Clean the areas where the intermediate shaft
contacts the transmission (differential) with solvent
or carburetor cleaner, and dry with compressed air.
Then install the intermediate shaft in the
differential. While installing the intermediate shaft,
be sure not to allow dust or other foreign particles
to enter the transmission.
03/07/29 09:33:46 61S0X050_140_0151
01
*01
10
14-149
EQS07AODSY0
A
12 x 1.25 mm
103 N·m
(10.5 kgf·m,
75.9 lbf·ft)
C
C
B
12 x 1.25 mm
117 N·m
(11.9 kgf·m, 86.1 lbf·ft)
A
A
B
12 x 1.25 mm
117 N·m
(11.9 kgf·m,
86.1 lbf·ft)
B
12 x 1.25 mm
74 N·m (7.5 kgf·m, 54 lbf·ft)
D
D
14. Install a new set ring on the right driveshaft.
15. Install the right and left driveshaft. While installing
the left driveshaft in the differential, be sure not to
allow dust or other foreign particles to enter the
transmission.
NOTE:
• Clean the areas where the left driveshaft contacts
the transmission (differential) with solvent or
carburetor cleaner, and dry with compressed air.
• Turn the right and left steering knuckle fully
outward, and slide the left driveshaft into the
differential until you feel its spring clip engage
the side gear. Slide the right driveshaft into the
intermediate shaft until you feel its spring clip
engage the intermediate shaft.
16. Support the front subframe with the front subframe
adapter (T/N EQS07AODSY0) and a jack, and lift it
up the body.
17. Loosely install the subframe mounting bolts (4) (A)
and the 12 x 1.25 mm bolts (6) (B) with the
stiffeners (C), then tighten the bolts to the specified
torque by aligning all reference marks (D).
(cont’d)
Replace.
03/07/29 09:33:47 61S0X050_140_0152
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст