Honda Odyssey 2004. Manual — part 189
11
12
13
14
14-150
Automatic Transmission
Transmission Installation (cont’d)
10 x 1.25 mm
38 N·m (3.9 kgf·m,
28 lbf·ft)
C
A
B
B
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
C
A
10 x 1.25 mm
38 N·m (3.9 kgf·m,
28 lbf·ft)
B
10 x 1.25 mm
58 N·m (5.9 kgf·m,
43 lbf·ft)
B
10 x 1.25 mm
39 N·m (4.0 kgf·m,
29 lbf·ft)
10 x 1.25 mm
59 N·m (6.0 kgf·m,
43 lbf·ft)
B
10 x 1.25 mm
58 N·m (5.9 kgf·m, 43 lbf·ft)
C
A
10 x 1.25 mm
59 N·m (6.0 kgf·m,
43 lbf·ft)
18. Install the transmission lower mount nuts.
19. Install the power steering fluid pipe (A) on the
clamps (B), and install the power steering fluid pipe
bracket (C).
20. Install the rear mount mounting bolts (A).
21. Install the steering gearbox mounting bolts (B) and
the stiffener (C).
22. Install the stiffener (A) and the steering gearbox
mounting bolt (B) with nut (C).
03/07/29 09:33:48 61S0X050_140_0153
15
06
16
*02
−
−
−
14-151
C
D
B
6 x 1.0 mm
9.8 N·m (1.0 kgf·m,
7.2 lbf·ft)
A
10 x 1.25 mm
39 N·m (4.0 kgf·m,
29 lbf·ft)
A
B
C
F
E
G
D
6 x 1.0 mm
14 N·m (1.4 kgf·m, 10 lbf·ft)
8 x 1.25 mm
22 N·m (2.2 kgf·m,
16 lbf·ft)
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
C
B
12 x 1.25 mm
59
69 N·m (6.0
7.0 kgf·m,
43
51 lbf·ft)
F
G
E
D
12 x 1.25 mm
78 N·m (7.0 kgf·m,
51 lbf·ft)
A
D
C
E
B
A
E
C
D
10 x 1.25 mm
33 N·m (3.4 kgf·m,
25 lbf·ft)
10 x 1.25 mm
54 N·m (5.5 kgf·m,
40 lbf·ft)
23. Install the steering gearbox mounting bolt (A) and
the power steering fluid pipe bracket bolts (B).
24. Install the power steering fluid return hose clip (C)
on the bracket (D).
25. Install the control lever (A) with the shift cable (B)
on the control shaft (C). Do not bend the shift cable
excessively.
26. Install the lock bolt (D) with a new lock washer (E),
then bend the lock washer tab against the bolt.
27. Install the shift cable cover (F), then install the shift
cable holder (G) on the shift cable cover.
NOTE: To prevent damage to the control lever, be
sure to install the shift cable holder after installing
the shift cable cover to the torque converter
housing.
28. Install the ball joints on each lower arms (A) with
the castle nuts (hex nuts) (B) and spring pins (C).
29. Install the nut (D) to the ball joint pin (E) on the
stabilizer link (F), then use a 6 mm Allen-type
wrench (G), and tighten the nut to the specified
torque.
30. Install the exhaust pipe A (A) and the three way
catalytic converter (B) assembly.
31. Connect the oxygen sensor connectors (C), then
install them on their connector brackets (D).
Install the harnesses on the clamps (E).
(cont’d)
Replace.
Replace.
03/07/29 09:33:50 61S0X050_140_0154
18
19
20
21
14-152
Automatic Transmission
Transmission Installation (cont’d)
12 x 1.25 mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
A
12 x 1.25 mm
54 N·m (5.5 kgf·m, 40 lbf·ft)
B
A
B
C
D
32. Install the splash shield.
33. Install the transmission housing mounting bolts.
34. Install and tighten the nut (A) on the front mount.
35. Connect the vacuum tube (B).
36. Remove the engine hanger.
37. Connect the A/T gear position switch connector (A),
then install it on its connector bracket (B).
38. Connect the connectors to the countershaft speed
sensor (C) and the 2nd clutch pressure switch (D).
Do not allow, fluid, oil, dust, or other foreign
particles to enter the connectors.
03/07/29 09:33:51 61S0X050_140_0155
22
23
24
14-153
D
A
B
C
8 x 1.25 mm
26 N·m (2.7 kgf·m,
20 lbf·ft)
8 x 1.25 mm
26 N·m (2.7 kgf·m,
20 lbf·ft)
C
B
A
D
A
B
6 x 1.0 mm
9.8 N·m (1.0 kgf·m,
7.2 lbf·ft)
9 N·m (0.9 kgf·m,
6.5 lbf·ft)
12 x 1.25 mm
64 N·m
(6.5 kgf·m,
47 lbf·ft)
C
E
E
10 x 1.25 mm
44 N·m (4.5 kgf·m, 33 lbf·ft)
39. Install the harness cover (A) on the transmission
hanger (B), then install the connector bracket (C).
40. Install the torque converter clutch solenoid valve/
shift solenoid valve A connector (D) on the harness
cover, then connect the connector.
41. Connect the connectors to the 3rd clutch pressure
switch (A), mainshaft speed sensor (B), and A/T
clutch pressure control solenoid valves A and B (C),
then install the clamps on the clamp brackets. Do
not allow fluid, oil, dust, or other foreign particles
to enter the connectors.
42. Connect the connectors to the shift solenoid valve
B (A) and shift solenoid valve C (B), then install the
clamp on the clamp bracket.
43. Install the transmission ground cable terminal (C).
44. Install the starter (D) on the torque converter
housing. Connect the starter cables (E) to the
starter, and install the harness clamp on the clamp
bracket. Make sure the crimped side of the starter
cable ring terminal is facing out.
(cont’d)
03/07/29 09:33:52 61S0X050_140_0156
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст