Honda Odyssey 2004. Manual — part 575
−
−
−
−
−
−
01
*01
S0X4AZBK791000R229XFAAT00
’03-04 Models
DTC 22-9x (22-90 to 22-99, 22-9A to 22-9F):
Special Tools Required
YES
NO
YES
NO
YES
NO
23-242
SRS
DTC Troubleshooting (cont’d)
07TAZ-SZ5011A
07SAZ-TB4011A
A
A
07TAZ-SZ5011A
07SAZ-TB4011A
C581
Short to Ground in Front Passenger’s Seat
Belt Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead C 07TAZ-SZ5011A
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s seat belt
tensioner 2P connector from the right side wire
harness (A).
5. Connect the special tool (2
connector) to the
right side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-38).
Go to step 9.
Short to ground in the front passenger’s seat
belt tensioner; replace the front passenger’s seat
belt (see page 23-4).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the SRS main harness 2P connector
C581 from the right side wire harness 2P
connector (A).
11. Connect the special tool (2
connector) to the SRS
main harness 4P connector.
12. Reconnect the battery negative cable.
13. Erase the DTC memory.
14. Read the DTC.
Go to step 15.
Short to ground in the right side wire harness;
replace the right side wire harness.
15. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Does the SRS indicator stay on?
Is DT C 22-9x indicated?
Is DT C 21-9x indicated?
03/07/29 10:38:09 61S0X050_230_0242
−
−
02
03
04
YES
NO
23-243
A
B
RED/YEL
RED/BLK
SRS UNIT CONNECTOR B (28P)
16. Disconnect the driver’s seat belt tensioner
connector (A).
17. Disconnect SRS unit connector B (28P) from the
SRS unit.
18. Disconnect the special tool from the SRS main
harness 2P connector.
19. Check resistance between the No. 3 terminal of
SRS unit connector B (28P) and body ground, and
between the No. 4 terminal and body ground.
There should be an open circuit, or at least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-384).
Go to step 20.
(cont’d)
Wire side of female terminals
Is the r esistance as specif ied?
03/07/29 10:38:10 61S0X050_230_0243
−
−
*02
06
YES
NO
23-244
SRS
DTC Troubleshooting (cont’d)
C851
A
RED/BLK
RED/YEL
SRS MAIN HARNESS 28P CONNECTOR
20. Disconnect SRS floor harness 28P connector (A)
from the SRS main harness 28P connector C851.
21. Check resistance between the No. 6 terminal of the
SRS main harness 28P connector and body ground,
and between the No. 15 terminal and body ground.
There should be an open circuit, or at least 1 M
.
Replace the SRS floor harness.
Replace the SRS main harness.
Wire side of female terminals
Is the r esistance as specif ied?
03/07/29 10:38:10 61S0X050_230_0244
−
−
−
−
01
01
02
S0X4ASIK791000R311XFAAT20
’03-04 Models
DTC 31-1x (31-10 to 31-19, 31-1A to 31-1F):
Special Tools Required
YES
NO
YES
NO
23-245
07SAZ-TB4011A
07XAZ-S1A0200
A
A
B
Open or Increased Resistance in Driver’s Side
Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead E 07XAZ-S1A0200
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the left side wire harness 2P connector
(A) from the driver’s side airbag.
5. Connect the special tool (2
connector) to the left
side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-38).
Go to step 9.
Open or increased resistance in the driver’s
side airbag inflator; replace the driver’s side airbag
(see page 23-372).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect both seat belt tensioner 2P connectors
from the side wire harness (A).
11. Disconnect SRS unit connector B (28P) from the
SRS unit. Do not disconnect the special tool from
the left side wire harness 2P connector.
(cont’d)
Does the SRS indicator stay on?
Is DT C 31-1x indicated?
03/07/29 10:38:11 61S0X050_230_0245
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст