Honda Odyssey 2004. Manual — part 576
−
−
−
−
03
*01
05
YES
NO
YES
NO
23-246
SRS
DTC Troubleshooting (cont’d)
LEFT SIDE WIRE HARNESS
2P CONNECTOR
07XAZ-S1A0200
C852
A
GRN/YEL
GRN
SRS FLOOR HARNESS 28P CONNECTOR
12. Disconnect the SRS inflator simulator from SRS
simulator lead E.
13. Check resistance between the terminals of SRS
simulator lead E. There should be 1.0
or less.
Faulty SRS unit or poor contact at SRS unit
connector B (28P) and the SRS unit. Check the
connection; if the connection is OK, replace the
SRS unit (see page 23-384).
Go to step 14.
14. Disconnect the SRS floor harness 28P connector (A)
from SRS floor subharness C852.
15. Check resistance between the No. 21 and No. 22
terminals of the SRS floor harness 28P connector.
There should be 1.0
or less.
Open or increased resistance in the SRS
floor subharness or left side wire harness; replace
the faulty harness.
Open or increased resistance in the SRS floor
harness; replace the SRS floor harness.
Terminal side of male terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:38:12 61S0X050_230_0246
−
−
−
−
01
01
02
S0X4ASIK791000R313XFAAT00
’03-04 Models
DTC 31-3x (31-30 to 31-39, 31-3A to 31-3F):
Special Tools Required
YES
NO
YES
NO
23-247
07SAZ-TB4011A
07XAZ-S1A0200
A
A
B
Short to Another Wire or Decreased
Resistance in Driver’s Side Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead E 07XAZ-S1A0200
• SRS short canceler 070AZ-SAA0100
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the left side wire harness 2P connector
(A) from the driver’s side airbag.
5. Connect the special tool (2
connector) to the left
side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-38).
Go to step 9.
Short to another wire in the driver’s side
airbag inflator; replace the driver’s side airbag.
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect both seat belt tensioner 2P connectors
from the side wire harness (A).
11. Disconnect SRS unit connector B (28P) from the
SRS unit.
(cont’d)
Does the SRS indicator stay on?
Is DT C 31-3x indicated?
03/07/29 10:38:13 61S0X050_230_0247
−
−
−
−
03
*01
05
YES
NO
YES
NO
23-248
SRS
DTC Troubleshooting (cont’d)
LEFT SIDE WIRE HARNESS
2P CONNECTOR
07XAZ-S1A0200
C852
A
GRN/YEL
GRN
SRS FLOOR HARNESS 28P CONNECTOR
12. Disconnect the SRS inflator simulator from SRS
simulator lead E.
13. Connect the special tool (070AZ-SAA0100) to No.
21 and No. 22 terminals of SRS unit connector B
(28P) (see page 23-26).
14. Check resistance between the terminals of SRS
simulator lead E. There should be an open circuit,
or at least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-384).
Go to step 15.
15. Disconnect the SRS floor harness 28P connector (A)
from SRS floor subharness C852.
16. Check resistance between the No. 21 and No. 22
terminals of the SRS floor harness 28P connector.
There should be an open circuit, or at least 1 M
.
Short in the SRS floor subharness or left side
wire harness; replace the faulty harness.
Short in the SRS floor harness; replace the
SRS floor harness.
Terminal side of male terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:38:13 61S0X050_230_0248
−
−
−
−
01
01
02
S0X4ASIK791000R318XFAAT00
’03-04 Models
DTC 31-8x (31-80 to 31-89, 31-8A to 31-8F):
Special Tools Required
YES
NO
YES
NO
23-249
07SAZ-TB4011A
07XAZ-S1A0200
A
A
B
Short to Power in Driver’s Side Airbag
Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead E 07XAZ-S1A0200
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the left side wire harness 2P connector
(A) from the driver’s side airbag.
5. Connect the special tool (2
connector) to the left
side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-38).
Go to step 9.
Short to power in the driver’s side airbag
inflator; replace the driver’s side airbag (see page
23-372).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect both seat belt tensioner 2P connectors
from the side wire harness (A).
11. Disconnect SRS unit connector B (28P) from the
SRS unit.
(cont’d)
Does the SRS indicator stay on?
Is DT C 31-8x indicated?
03/07/29 10:38:14 61S0X050_230_0249
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст