Honda Odyssey 2004. Manual — part 568
−
−
−
−
05
*01
04
YES
NO
YES
NO
23-214
SRS
DTC Troubleshooting (cont’d)
SRS
MAIN HARNESS
4P CONNECTOR
07XAZ-SZ30100
A
C851
SRS FLOOR HARNESS 28P CONNECTOR
WHT
RED/YEL
BLU/YEL
YEL
12. Check resistance between the terminals of the SRS
simulator lead F. There should be 1
or less.
Faulty SRS unit or poor contact at SRS unit
connector A (28P). Check the connection; if the
connection is OK, replace the SRS unit (see page
23-384).
Go to step 13.
13. Disconnect the SRS floor harness 28P connector (A)
from SRS main harness connector C851.
14. Check resistance between the No. 7 and No. 8
terminals and between the No. 1 and No. 2
terminals of the SRS floor harness 28P connector.
There should be 1
or less.
Open or increased resistance in the SRS
main harness; replace the SRS main harness.
Open or increased resistance in the SRS floor
harness; replace the SRS floor harness.
Terminal side of male terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:37:51 61S0X050_230_0214
−
−
−
−
01
01
S0X4AZBK791000R123XFAAT00
’03-04 Models
DTC 12-3x (12-30 to 12-39, 12-3A to 12-3F):
DTC 12-6x (12-60 to 12-69, 12-6A to 12-6F):
Special Tools Required
YES
NO
YES
NO
23-215
A
07XAZ-SZ30100
07SAZ-TB4011A
A
Short to Another Wire or Decreased
Resistance in Front Passenger’s Airbag First
Inflator
Short to Another Wire or Decreased
Resistance in Front Passenger’s Airbag
Second Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
• SRS short canceler 070AZ-SAA0100
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s airbag 4P
connector from the SRS main harness (A).
5. Connect the special tool (2
connectors) to the
SRS main harness 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-38).
Go to step 9.
Short in the front passenger’s airbag first or
second inflator; replace the front passenger’s
airbag (see page 23-370).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect SRS unit connector A (28P) from the
SRS unit.
11. Disconnect the SRS inflator simulator from the SRS
simulator lead F.
12. Connect the special tool (070AZ-SAA0100) to No. 9
and No. 10 terminals or No. 3 and No. 4 terminals
of SRS unit connector A (28P) (see page 23-26).
(cont’d)
Does the SRS indicator stay on?
Is DT C 12-3x or 12-6x indicated?
03/07/29 10:37:52 61S0X050_230_0215
−
−
−
−
05
*01
04
YES
NO
YES
NO
23-216
SRS
DTC Troubleshooting (cont’d)
SRS
MAIN HARNESS
4P CONNECTOR
07XAZ-SZ30100
A
C851
SRS FLOOR HARNESS 28P CONNECTOR
WHT
RED/YEL
BLU/YEL
YEL
13. Check resistance between the terminals of the SRS
simulator lead F. There should be an open circuit,
or at least 1 M
.
Replace the SRS unit (see page 23-384).
Go to step 14.
14. Disconnect the SRS floor harness 28P connector (A)
from SRS main harness connector C851.
15. Check resistance between the No. 7 and No. 8
terminals and between the No. 1 and No. 2
terminals of the SRS floor harness 28P connector.
There should be an open circuit, or at least 1 M
.
Short in the SRS main harness; replace the
SRS main harness.
Short in the SRS floor harness; replace the
SRS floor harness.
Terminal side of male terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:37:53 61S0X050_230_0216
−
−
−
−
01
01
S0X4AZBK791000R128XFAAT00
’03-04 Models
DTC 12-8x (12-80 to 12-89, 12-8A to 12-8F):
DTC 12-Ax (12-A0 to 12-A9, 12-AA to 12-AF):
Special Tools Required
YES
NO
YES
NO
23-217
A
07XAZ-SZ30100
07SAZ-TB4011A
A
Short to Power in Front Passenger’s Airbag
First Inflator
Short to Power in Front Passenger’s Airbag
Second Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s airbag 4P
connector from the dashboard wire harness (A).
5. Connect the special tool (2
connectors) to the
SRS main harness 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-38).
Go to step 9.
Short to power in the front passenger’s airbag
first or second inflator; replace the front passenger’s
airbag (see page 23-370).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect SRS unit connector A (28P) from the
SRS unit.
11. Reconnect the battery negative cable.
12. Disconnect the SRS inflator simulator from SRS
simulator lead F.
13. Turn the ignition switch ON (II).
(cont’d)
Does the SRS indicator stay on?
Is DT C 12-8x or 12-Ax indicated?
03/07/29 10:37:53 61S0X050_230_0217
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст