Honda Odyssey 2004. Manual — part 566
−
−
04
*03
YES
NO
23-206
SRS
DTC Troubleshooting (cont’d)
A
SRS FLOOR HARNESS 28P CONNECTOR C851
GRN/YEL
GRN/WHT
GRN
GRN/
BLK
15. Disconnect SRS unit connector A (28P) from the
SRS unit.
16. Connect the special tool (070AZ-SAA0100) to the
No. 7 and No. 8 terminals or the No. 1 and No. 2
terminals of SRS unit connector A (28P) (see page
23-26).
17. Check resistance between the No. 9 and No. 10
terminals of the SRS floor harness 28P connector
C851, and between the No. 3 and No. 4 terminals.
There should be an open circuit, or at least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-384).
Replace the SRS floor harness.
Terminal side of male terminals
Is the r esistance as specif ied?
03/07/29 10:37:47 61S0X050_230_0206
−
−
−
−
01
01
S0X4AZBK791000R118XFAAT00
’03-04 Models
DTC 11-8x (11-80 to 11-89, 11-8A to 11-8F):
DTC 11-Ax (11-A0 to 11-A9, 11-AA to 11-AF):
Special Tools Required
YES
NO
YES
NO
23-207
A
07XAZ-SZ30100
07SAZ-TB4011A
A
Short to power in Driver’s Airbag First
Inflator
Short to power in Driver’s Airbag Second
Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s airbag 4P connector from
the cable reel (A).
5. Connect the special tool (2
connectors) to the
cable reel 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-38).
Go to step 9.
Short to power in the driver’s airbag first or
second inflator; replace the driver’s airbag (see
page 23-368).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect SRS unit connector A (28P) from the
SRS unit.
11. Reconnect the battery negative cable.
12. Turn the ignition switch ON (II).
13. Disconnect the SRS inflator simulator from SRS
simulator lead F.
(cont’d)
Does the SRS indicator stay on?
Is DT C 11-8x or 11-Ax indicated?
03/07/29 10:37:48 61S0X050_230_0207
−
−
−
−
02
03
YES
NO
YES
NO
23-208
SRS
DTC Troubleshooting (cont’d)
CABLE
REEL 4P CONNECTOR
07XAZ-SZ30100
CABLE
REEL 4P CONNECTOR
07XAZ-SZ30100
14. Check for voltage between each terminal of SRS
simulator lead F and body ground. There should be
0.5 V or less.
Faulty SRS unit; replace the SRS unit (see
page 23-384).
Go to step 15.
15. Turn the ignition switch OFF.
16. Disconnect the SRS main harness 4P connector
from the cable reel.
17. Turn the ignition switch ON (II).
18. Check for voltage between each terminal of SRS
simulator lead F and body ground. There should be
0.5 V or less.
Go to step 19.
Replace the cable reel (see page 23-377).
Is the voltage as specif ied?
Is the voltage as specif ied?
03/07/29 10:37:48 61S0X050_230_0208
−
−
*01
05
YES
NO
23-209
A
C851
SRS FLOOR HARNESS 28P CONNECTOR
GRN/YEL
GRN/WHT
GRN
GRN/BLK
19. Turn the ignition switch OFF.
20. Disconnect the SRS floor harness 28P connector (A)
from SRS main harness connector C851.
21. Turn the ignition switch ON (II).
22. Check for voltage between the No. 9 terminal of
SRS floor harness 28P connector and body ground,
the No. 10 terminal and body ground, the No. 3
terminal and body ground, and the No. 4 terminal
and body ground. There should be 0.5 V or less.
Replace the SRS main harness.
Replace the SRS floor harness.
Terminal side of male terminals
Is the voltage as specif ied?
03/07/29 10:37:49 61S0X050_230_0209
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст