Honda Odyssey 2004. Manual — part 567
−
−
−
−
01
01
S0X4AZBK791000R119XFAAT00
’03-04 Models
DTC 11-9x (11-90 to 11-99, 11-9A to 11-9F):
DTC 11-Bx (11-B0 to 11-B9, 11-BA to 11-BF):
Special Tools Required
YES
NO
YES
NO
23-210
SRS
DTC Troubleshooting (cont’d)
A
07XAZ-SZ30100
07SAZ-TB4011A
A
Short to Ground in Driver’s Airbag First
Inflator
Short to Ground in Driver’s Airbag Second
Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s airbag 4P connector from
the cable reel (A).
5. Connect the special tool (2
connectors) to the
cable reel 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-38).
Go to step 9.
Short to ground in the driver’s airbag first or
second inflator; replace the driver’s airbag (see
page 23-368).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect SRS unit connector A (28P) from the
SRS unit.
11. Disconnect the SRS inflator simulator from SRS
simulator lead F.
Does the SRS indicator stay on?
Is DT C 11-9x, or 11-Bx indicated?
03/07/29 10:37:49 61S0X050_230_0210
−
−
−
−
02
03
YES
NO
YES
NO
23-211
CABLE
REEL 4P CONNECTOR
07XAZ-SZ30100
CABLE
REEL 4P CONNECTOR
07XAZ-SZ30100
12. Check resistance between each terminal of SRS
simulator lead F and body ground. There should be
an open circuit, or at least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-384).
Go to step 13.
13. Disconnect the SRS main harness 4P connector
from the cable reel 4P connector.
14. Check resistance between each terminal of SRS
simulator lead F and body ground. There should be
an open circuit, or at least 1 M
.
Go to step 15.
Replace the cable reel (see page 23-377).
(cont’d)
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:37:50 61S0X050_230_0211
−
−
*01
05
YES
NO
23-212
SRS
DTC Troubleshooting (cont’d)
A
C851
SRS FLOOR HARNESS 28P CONNECTOR
GRN/YEL
GRN/WHT
GRN
GRN/BLK
15. Disconnect the SRS floor harness 28P connector (A)
from SRS main harness connector C851.
16. Check resistance between the No. 9 terminal of the
SRS floor harness 28P connector and body ground,
the No. 10 terminal and body ground, the No. 3
terminal and body ground, and No. 4 terminal and
body ground. There should be an open circuit, or at
least 1 M
.
Replace the SRS main harness.
Replace the SRS floor harness.
Terminal side of male terminals
Is the r esistance as specif ied?
03/07/29 10:37:50 61S0X050_230_0212
−
−
−
−
01
01
S0X4AZBK791000R121XFAAT20
’03-04 Models
DTC 12-1x (12-10 to 12-19, 12-1A to 12-1F):
DTC 12-4x (12-40 to 12-49, 12-4A to 12-4F):
Special Tools Required
YES
NO
YES
NO
23-213
A
07XAZ-SZ30100
07SAZ-TB4011A
A
Open or Increased Resistance in Front
Passenger’s Airbag First Inflator
Open or Increased Resistance in Front
Passenger’s Airbag Second Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s airbag 4P
connector from the SRS main harness (A).
5. Connect the special tool (2
connectors) to the
SRS main harness 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-38).
Go to step 9.
Open or increased resistance in the front
passenger’s airbag first or second inflator; replace
the front passenger’s airbag (see page 23-370).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect SRS unit connector A (28P) from the
SRS unit. Do not disconnect the special tool from
the SRS main harness.
11. Disconnect the SRS Inflator simulator from SRS
simulator lead F.
(cont’d)
Does the SRS indicator stay on?
Is DT C 12-1x or 12-4x indicated?
03/07/29 10:37:51 61S0X050_230_0213
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст