Honda Odyssey 2004. Manual — part 377
01
S0X4A00G24100049601KBAT00
20-150
Fenderwell
Rear Air Outlet Replacement
B
A
A
1. Remove the rear bumper (see page 20-130).
2. Detach the hooks (A), then remove the rear air
outlet (B). Take care not to scratch the body.
3. Install the air outlet in the reverse order of removal.
03/07/29 10:04:06 61S0X050_200_0152
01
S0X4A00J18533232001DAAT00
20-151
Openers
Component Location Index
TAILGATE LOCK
CYLINDER
HOOD OPENER CABLE
TAILGATE LATCH
FUEL FILL DOOR LATCH
FUEL FILL DOOR OPENER
HOOD RELEASE HANDLE
HOOD LATCH
TAILGATE HANDLE
FUEL FILL DOOR OPENER CABLE
Replacement, page 20-158
Replacement, page 20-152
Replacement, page 20-158
Replacement, page 20-156
Replacement, page 20-155
Replacement, page 20-154
Replacement, page 20-154
Replacement,
page 20-157
Replacement, page 20-153
03/07/29 10:04:08 61S0X050_200_0153
01
S0X4A00J18533232001KBAT00
20-152
Openers
Hood Opener Cable Replacement
Fastener Locations
D
E
: Clip, 1
: Clip, 1
A
B
E
C
D
1. Remove the following parts from the left side of the vehicle:
• Inner fender (see page 20-149)
• Kick panel (see page 20-58)
2. Remove the hood latch (A) (see page 20-154), and disconnect the hood opener (B).
3. Remove the hood release handle (C) (see page 20-154), and disconnect the hood opener cable.
4. Using a clip remover, detach the clips (D, E) from the body, then remove the hood opener cable from the vehicle.
Take care not to kink the cable.
5. Install the cable in the reverse order of removal, and replace any damaged clips.
03/07/29 10:04:08 61S0X050_200_0154
01
S0X4A00J18526327912KBAT00
20-153
Fuel Fill Door Opener Cable Replacement
Fastener Locations
C
: Clip, 2
D
: Cushion tape, 2
E
F
: Clip, 1
: Clip, 1
F
G
D
F
E
D
C
C
A
B
For ’02-04 models: SRS components are located in this area. Review the SRS component locations, ’02 model (see
page 23-19), ’03-04 models (see page 23-20), and the precautions and procedures (see page 23-21) before performing
repairs or service.
1. Remove these items:
• Front door sill trim, left side (see page 20-58)
• Sliding door sill trim, left side (see page 20-58)
• Rear side trim panel (see page 20-60)
• Third row seat belt retractor (see page 23-11)
2. Pull the carpet back as necessary (see page 20-65).
3. Disconnect the fuel fill door opener cable (A) from the opener (B) (see step 4 on page 20-156).
4. Release the opener cable from the clips (C, E, F) and remove the cable cushion (D), then remove the fuel fill door
latch (G) from the body.
5. Install the cable in the reverse order of removal, and replace any damaged clips.
6. Check the operation of the sliding door; verify that the left sliding door locks when the fuel filler door release is
pulled.
03/07/29 10:04:08 61S0X050_200_0155
• Quarter plastic cover (see page 20-6)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст