Honda Odyssey 2004. Manual — part 271
01
S0X4AA1E10411627001KBAT00
01
02
S0X4AA1E10411619611KBAT00
Torque:
101 N·m (10.3 kgf·m, 74.5 lbf·ft)
Special Tools Required
14-478
14-478
A/T Differential
Differential Carrier, Final Driven
Gear Replacement
Carrier Bearing Replacement
B
C
D
A
07LAD-PW50601
1. Remove the final driven gear from the differential
carrier.
NOTE: The final driven gear bolts have left-hand
threads.
2. Install the final driven gear with the chamfered side
on the inner bore facing the differential carrier.
3. Tighten the bolts to the specified torque in a
crisscross pattern.
Attachment, 40 x 50 mm 07LAD-PW50601
NOTE:
• The bearing and outer race should be replaced as a
set.
• Inspect and adjust the bearing preload whenever
bearing is replaced.
• Check the bearing for wear and rough rotation. If the
bearing is OK, removal is not necessary.
1. Remove the carrier bearing (A) with a commercially
available bearing puller (B), bearing separator (C),
and stepped adapter (D).
2. Install the new carrier bearings with the special tool
and a press.
NOTE:
• Press the bearing on until it bottoms.
• Use the small end of the special tool to install the
bearing.
• Press the bearing on securely so there is no
clearance between the bearing and the
differential carrier.
03/07/29 09:46:30 61S0X050_140_0481
*01
*02
01
02
S0X4AA1E10411619631KBAT00
Special Tools Required
14-479
Oil Seal Replacement
A
B
A
B
A
07GAD-PG40101 or
07GAD-PG40100
07749-0010000
07JAD-PH80101
07749-0010000
A
• Driver 07749-0010000
• Seal driver attachment
07GAD-PG40101 or 07GAD-PG40100
• Oil seal driver attachment 07JAD-PH80101
1. Remove the differential assembly.
2. Remove the oil seal (A) from the transmission
housing (B).
3. Remove the oil seal (A) from the torque converter
housing (B).
4. Install the oil seal (A) in the transmission housing
with the special tools.
5. Install the oil seal (A) in the torque converter
housing with the special tools.
03/07/29 09:46:31 61S0X050_140_0482
*01
*02
*03
S0X4AA1E10411619601KBAT00
Special Tools Required
14-480
A/T Differential
Carrier Bearing Outer Race Replacement
C
B
A
D
07749-0010000
07NAD-PX40100
B
A
C
07749-0010000
07NAD-PX40100
• Driver 07749-0010000
• Attachment, 78 x 80 mm 07NAD-PX40100
NOTE:
• Replace the bearing with a new one whenever the
outer race is replaced.
• Do not use shim(s) on the torque converter housing
side.
• Adjust preload after replacing the bearing and outer
race.
• Coat all parts with ATF during installation.
1. Remove the bearing outer race from the
transmission housing by heating the housing to
about 212°F (100°C) with a heat gun. Do not heat
the housing to more than 212°F (100°C).
2. Remove the bearing outer race from the torque
converter housing.
3. Install the thrust shim (A), thrust washer (B), and
outer race (C) in the transmission housing (D) with
the special tools.
4. Install the thrust washer (A) and outer race (B) in
the torque converter housing (C), and use the
special tools to make sure the outer race bottoms
out in the housing.
03/07/29 09:46:31 61S0X050_140_0483
*01
*02
*03
S0X4AA1E10411619611MAAT00
Special Tools Required
14-481
Carrier Bearing Preload Inspection
E
D
C
B
A
C
B
A
D
07749-0010000
07NAD-PX40100
• Driver 07749-0010000
• Attachment, 78 x 80 mm 07NAD-PX40100
• Preload inspection tool 07YAJ-S3V0100
NOTE: If the transmission housing, torque converter
housing, differential carrier, tapered roller bearing,
outer race, or thrust shim were replaced, the bearing
preload must be adjusted.
1. Remove the bearing outer race (A), thrust washer
(B), and thrust shim (C) from the transmission
housing (D) by heating the housing to about 212°F
(100°C) with a heat gun (E). Do not heat the housing
to more than of 212°F (100°C).
NOTE: Let the transmission housing cool to room
temperature before adjusting the bearing preload.
2. Replace the tapered roller bearing when the outer
race is to be replaced.
3. Do not use a shim on the torque converter housing
side.
4. Install the 81 mm thrust shim (A), thrust washer (B),
and bearing outer race (C) in the transmission
housing. If you replace the 81 mm thrust shim with
a new one, use the same thickness shim as the old
one.
5. Drive in the outer race with the special tools.
6. Check that there is no clearance between the thrust
washer, outer race, shim, and transmission
housing.
(cont’d)
03/07/29 09:46:32 61S0X050_140_0484
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст