Honda Odyssey 2004. Manual — part 272
−
−
−
−
−
−
01
01
Standard:
New bearing:
2.7
3.9 N·m
(28
40 kgf·cm, 24
35 lbf·in.)
Reused bearings:
2.5
3.6 N·m
(25
37 kgf·cm, 22
32 lbf·in.)
14-482
A/T Differential
Carrier Bearing Preload Inspection (cont’d)
10 x 1.25 mm
44 N·m
(4.5 kgf·m, 33 lbf·ft)
H
G
G
C
B
D
A
C
E
F
07YAJ-S3V0100
A
B
7. Install the differential assembly (A), gasket (B), and
dowel pins (C) on the torque converter housing (D).
Align the spring pin on the control shaft (E) with the
transmission housing groove.
8. Install the transmission housing (F) with the
transmission hangers (G) and harness clamp
bracket (H), then tighten the bolts.
9. Rotate the differential assembly in both directions
to seat the bearings.
10. Measure the starting torque of the differential
assembly with the special tools, a torque
wrench (A) and a socket (B). Measure the starting
torque at normal room temperature in both
directions.
03/07/29 09:46:33 61S0X050_140_0485
−
−
−
THRUST SHIM, 81 mm
No.
Part Number
Thickness
14-483
11. If the measurement is out of standard, remove the
thrust shim and select the thrust shim from table.
Install the new thrust shim and recheck. To
increase the starting torque, increase the thickness
of the thrust shim. To decrease the starting torque,
decrease the thickness of the thrust shim. Changing
the shim to the next size will increase or decrease
starting torque about 0.3
0.4 N·m (3
4 kgf·cm,
2
3 lbf·in.).
A
41438-P7T-700
2.05 mm (0.081 in.)
AA
41438-PGH-000
2.075 mm (0.082 in.)
B
41439-P7T-700
2.10 mm (0.083 in.)
BB
41439-PGH-000
2.125 mm (0.084 in.)
C
41440-P7T-700
2.15 mm (0.085 in.)
CC
41440-PGH-000
2.175 mm (0.086 in.)
D
41441-P7T-000
2.20 mm (0.087 in.)
DD
41441-PGH-000
2.225 mm (0.088 in.)
E
41442-P7T-000
2.25 mm (0.089 in.)
EE
41442-PGH-000
2.275 mm (0.090 in.)
F
41443-P7T-000
2.30 mm (0.091 in.)
FF
41443-PGH-000
2.325 mm (0.092 in.)
G
41444-P7T-000
2.35 mm (0.093 in.)
GG
41444-PGH-000
2.375 mm (0.094 in.)
H
41445-P7T-000
2.40 mm (0.094 in.)
HH
41445-PGH-000
2.425 mm (0.095 in.)
I
41446-P7T-000
2.45 mm (0.096 in.)
II
41446-PGH-000
2.475 mm (0.097 in.)
J
41447-P7T-000
2.50 mm (0.098 in.)
JJ
41447-PGH-000
2.525 mm (0.099 in.)
K
41448-P7T-000
2.55 mm (0.100 in.)
KK
41448-PGH-000
2.575 mm (0.101 in.)
L
41449-P7T-000
2.60 mm (0.102 in.)
LL
41449-PGH-000
2.625 mm (0.103 in.)
M
41450-P7T-000
2.65 mm (0.104 in.)
MM
41450-PGH-000
2.675 mm (0.105 in.)
N
41451-P7T-000
2.70 mm (0.106 in.)
NN
41451-PGH-000
2.725 mm (0.107 in.)
O
41452-P7T-000
2.75 mm (0.108 in.)
OO
41452-PGH-000
2.775 mm (0.109 in.)
P
41453-P7T-000
2.80 mm (0.110 in.)
PP
41453-PGH-000
2.825 mm (0.111 in.)
Q
41454-P7T-000
2.85 mm (0.112 in.)
41454-PGH-000
2.875 mm (0.113 in.)
R
41455-P7T-000
2.90 mm (0.114 in.)
RR
41455-PGH-000
2.925 mm (0.115 in.)
S
41456-P7T-000
2.95 mm (0.116 in.)
SS
41456-PGH-000
2.975 mm (0.117 in.)
T
41457-P7T-000
3.00 mm (0.118 in.)
TT
41457-PGH-000
3.025 mm (0.119 in.)
U
41458-P7T-000
3.05 mm (0.120 in.)
03/07/29 09:46:34 61S0X050_140_0486
S0X4A000000000J1403ZAAT00
03/07/29 09:46:34 61S0X050_140_0487
S0X4A000000000J1601ZCAT00
Transaxle
Driveline/Axle
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . ..
. . . . . . . . . . . . . .
. . . . . . . . . . . ..
. . . . . . . . . . . ...
. . . . . . . . . . . . .
. . . . . . . . . ...
. . . . . . . .
. . . . . . . . .
. . . . . . . . ...
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . ..
. . . . . . . . . . . . . .
. . . . . . . . . . . ..
. . . . . . . . . . . ...
. . . . . . . . . . . . .
. . . . . . . . . ...
. . . . . . . .
. . . . . . . . .
. . . . . . . . ...
Special Tools
. 16-2
Driveshaft Inspection
. 16-3
Driveshaft Removal
. 16-3
Driveshaft Disassembly
. 16-5
Driveshaft Reassembly
. 16-9
Driveshaft Installation
. 16-16
Intermediate Shaft Removal
. 16-17
Intermediate Shaft Disassembly
. 16-18
Intermediate Shaft Reassembly
. 16-19
Intermediate Shaft Installation
. 16-21
03/07/29 09:47:20 61S0X050_160_0001
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст