Honda Odyssey 2004. Manual — part 270
03
04
14-474
Transmission End Cover
End Cover, 3rd Gear, Idler Gear, and 3rd Clutch Installation (cont’d)
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
B
E
A
D
C
G
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
C
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
H
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
22 N·m
(2.2 kgf·m,
16 lbf·ft)
J
28 N·m
(2.9 kgf·m,
21 lbf·ft)
K
I
F
L
B
D
E
39. Place the new ATF passage body gasket (A) on the
transmission housing, then install the 8 x 14 mm
dowel pin (B) and the 10 x 25.5 mm ATF feed pipe
(C) with the new O-ring (D). Install the ATF passage
body (E) on the transmission housing, if it was
removed.
40. Install the new ATF filter (A) on the transmission
housing.
41. Install the filter line bracket (B) on the ATF filter,
and loosely install the bolts (C).
42. Install the new O-ring (D) to the filter line (E), then
install the filter line on the ATF filter.
43. Secure the end of the filter line on the bracket (F)
with the bolt (G).
44. Secure the filter line on the filter line bracket with
the bolts (H).
45. Tighten the bolts (C) on the filter line bracket to the
specified torque.
46. Install the ATF hose (I) and line bolt (J) with the new
sealing washers (K).
47. Connect the hose to the filter line, and secure it
with the clip (L).
03/07/29 09:46:25 61S0X050_140_0477
05
*15
*16
06
14-475
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
12 x 1.25 mm
28 N·m
(2.9 kgf·m,
21 lbf·ft)
8 x 1.25 mm
26 N·m (2.6 kgf·m, 20 lbf·ft)
B
C
A
A
Clearance: 2 mm (0.08 in.)
A
C
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
D
E
F
48. Install the ATF cooler lines (A) with the new sealing
washers (B) and the line bolts, then install the
harness clamp bracket (C).
49. Set the transmission range switch to the N position.
NOTE: The transmission range switch clicks in the
N position.
50. Set the control shaft (A) to the N position by turning
it.
NOTE: Be careful not to squeeze the end of the
control shaft tips together when turning into
position. If the tips are squeezed together it will
cause a faulty signal or position due to the play
between the control shaft and the switch.
51. Install the transmission range switch (A) gently on
the control shaft (B). Do not move the transmission
range switch when tightening its bolts.
52. Install the transmission range switch cover (C);
secure the harness with the bolt on the end cover
(D); install the harness clips (E) on the brackets (F).
(cont’d)
03/07/29 09:46:26 61S0X050_140_0478
07
14-476
Transmission End Cover
End Cover, 3rd Gear, Idler Gear, and 3rd Clutch Installation (cont’d)
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
G
H
F
C
E
D
B
D
A
53. Connect the 3rd clutch pressure switch connector
(A) and A/T wire harness ground terminal (B) on the
connector bracket (C), then install the clips (D) on
the bracket (E).
54. Install the switch cover (F).
55. Install the ATF temperature sensor (G) with the new
O-ring (H), then secure the harness with the bolts.
Connect the sensor connector to the A/T wire
harness connector, then install it on the connector
bracket (C).
56. Install the dipstick.
03/07/29 09:46:27 61S0X050_140_0479
−
−
*01
S0X4AA1E10411600000DAAT00
01
S0X4AA1E10411600000MAAT00
Standard:
0.175
0.275 mm (0.007
0.011 in.)
14-477
14-477
A/T Differential
Component Location Index
Backlash Inspection
THRUST SHIM, 81 mm
THRUST WASHER
CARRIER BEARING
BEARING OUTER RACE
FINAL DRIVEN
GEAR
DIFFERENTIAL CARRIER
CARRIER BEARING
BEARING OUTER RACE
THRUST WASHER
C
B
A
A
1. Install both axles, and place the differential
assembly on V-blocks (A).
2. Check the backlash of the pinion gears (B) with a
dial indicator (C).
3. If the backlash is out of standard, replace the
differential carrier.
Replacement, page 14-478
Replacement, page 14-480
Replacement,
page 14-478
Backlash Inspection,
page 14-477
Replacement, page 14-478
Replacement, page 14-480
03/07/29 09:46:29 61S0X050_140_0480
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст