Honda Odyssey 2004. Manual — part 495
−
−
−
−
−
−
−
−
−
−
S0X4A00J16160700000FAAT00
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
22-308
Power Sliding Doors
Power Sliding Door Troubleshooting
1. Verify the customer’s complaint using ALL three of
the following methods:
• Using the driver’s switch to OPEN/CLOSE both
doors
• Using the keyless transmitter to OPEN/CLOSE
both doors
• Using the inner and outer handles to OPEN/
CLOSE both doors
Intermittent problem, inspect all
connections.
Go to step 2.
2. Check the fuses.
Go to step 3.
Find and repair the cause of the blown fuse.
3. Open and close the doors again using all three
methods, and listen for the warning beeper.
Go to step 4.
Go to step 5.
4. With the MAIN switch turned OFF, compare the
manual door opening/closing force between the
left and right doors.
Go to step 5.
Inspect the door guides, rollers, and cables on
the door that exhibited the higher opening/closing
force.
5. Check for codes.
Perform the troubleshooting (see page 22-
290).
Refer to the Symptom Troubleshooting Index
or perform the input test (see page 22-300).
Do the door s oper ate pr oper ly using all thr ee
methods?
Ar e the f uses OK ?
Did the war ning beeper sound thr ee times when all
thr ee opening methods wer e used?
Is the opening/ closing f or ce equal on both sides?
Ar e ther e any codes stor ed?
03/07/29 10:27:16 61S0X050_220_0310
01
*01
S0X4A00J16160755691FEAT01
01
S0X4A00J16160755635FEAT02
[ ]
[ ]
[ ]
22-309
22-309
Slide Motor Test
Sliding Door Buzzer Test
B
A
Terminal
Direction
OPEN
CLOSE
1
2
2
1
: Right side
A
B
1. Remove the rear side trim panel (see page 20-60).
2. Disconnect the 2P connector (A) from the slide
motor (B).
3. Check slide motor operation by connecting battery
power and ground according to the table.
The doors move very quickly. Do not allow
the motor to slam the door open or closed.
4. If the motor does not run or fails to run smoothly,
replace it.
1. Remove the left rear side trim panel (see page 20-
60).
2. Disconnect the 2P connector (A) from the buzzer (B).
3. Test the buzzer by connecting battery power to the
No. 1 terminal and grounding to the No. 2 terminal.
The buzzer should sound.
4. If the buzzer does not sound or fails to sound,
replace it.
Terminal side of
male terminals
Terminal side of
male terminals
03/07/29 10:27:17 61S0X050_220_0311
01
02
*01
01
S0X4A00J16160755641FEAT00
22-310
Power Sliding Doors
Closer Motor and Latch Position Switch Test
Not used
Terminal
Position
FULL LATCH
HALF LATCH
B4
B5
B6
OPEN
STRIKER
HALF LATCH
ON POSITION
(0.29 in (7.3 mm))
FULL LATCH
ON POSITION
(0.20 in (5 mm))
Terminal
Direction
FORWARD
REVERSE
B1
B3
1. Remove the sliding door panel (see page 20-13).
2. Disconnect the 6P connector from the motor and
switch.
3. Test the closer motor by connecting power and
ground according to the table.
4. Check for continuity between the terminals in each
switch position according to the table.
5. If the motor does not operate as specified or the
continuity is not as specified, replace the unit.
Terminal side of
male terminals
03/07/29 10:27:18 61S0X050_220_0312
01
02
03
S0X4A00J16160755681FEAT00
22-311
Release Motor and Remote Control Switch Test
YEL/RED
BLU
BLK
WHT/RED
Terminal
Direction
OPEN
C1
C2
Terminal
Position
HANDLE SWITCH ON
C3
C4
HANDLE SWITCH OFF
1. Remove the sliding door panel (see page 20-13).
2. Disconnect the 4P connector from the release
motor and switch.
3. Test the release motor by connecting power and
ground according to the table.
4. Check for continuity between the terminals in each
switch position according to the table.
5. If the actuator does not operate as specified or the
continuity is not as specified, replace the unit.
Wire side of
female terminals
03/07/29 10:27:18 61S0X050_220_0313
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст