Honda Odyssey 2004. Manual — part 577
−
−
−
−
03
*01
05
YES
NO
YES
NO
23-250
SRS
DTC Troubleshooting (cont’d)
LEFT SIDE WIRE HARNESS
2P CONNECTOR
07XAZ-S1A0200
C852
A
GRN/YEL
GRN
SRS FLOOR HARNESS 28P CONNECTOR
12. Reconnect the battery negative cable.
13. Disconnect the SRS inflator simulator from the SRS
simulator lead E.
14. Turn the ignition switch ON (II).
15. Check for voltage between each terminal of SRS
simulator lead E and body ground. There should be
0.5 V or less.
Faulty SRS unit; replace the SRS unit (see
page 23-384).
Go to step 16.
16. Turn the ignition switch OFF.
17. Disconnect the SRS floor harness 28P connector (A)
from the SRS floor subharness C852.
18. Turn the ignition switch ON (II).
19. Check for voltage between the No. 21 terminal of
the SRS floor harness 28P connector and body
ground, and between the No. 22 terminal and body
ground. There should be 0.5 V or less.
Short to power in the SRS floor subharness
or left side wire harness; replace the faulty
harness.
Short to power in the SRS floor harness;
replace the SRS floor harness.
Terminal side of male terminals
Is the voltage as specif ied?
Is the voltage as specif ied?
03/07/29 10:38:15 61S0X050_230_0250
−
−
−
−
01
01
02
S0X4ASIK791000R319XFAAT00
’03-04 Models
DTC 31-9x (31-90 to 31-99, 31-9A to 31-9F):
Special Tools Required
YES
NO
YES
NO
23-251
07SAZ-TB4011A
07XAZ-S1A0200
A
A
B
Short to Ground in Driver’s Side Airbag
Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead E 07XAZ-S1A0200
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the left side wire harness 2P connector
(A) from the driver’s side airbag.
5. Connect the special tool (2
connector) to the left
side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-38).
Go to step 9.
Short to ground in the driver’s side airbag
inflator; replace the driver’s side airbag (see page
23-372).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect both seat belt tensioner 2P connectors
from the side wire harness (A).
11. Disconnect SRS unit connector B (28P) from the
SRS unit.
(cont’d)
Does the SRS indicator stay on?
Is DT C 31-9x indicated?
03/07/29 10:39:27 61S0X050_230_0251
−
−
−
−
03
*01
*02
YES
NO
YES
NO
23-252
SRS
DTC Troubleshooting (cont’d)
LEFT SIDE WIRE HARNESS
2P CONNECOTOR
07XAZ-S1A0200
C852
A
GRN
SRS FLOOR HARNESS 28P CONNECTOR
GRN/YEL
12. Disconnect the SRS inflator simulator from SRS
simulator lead E.
13. Check resistance between each terminal of SRS
simulator lead E and body ground. There should be
an open circuit, or at least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-384).
Go to step 14.
14. Disconnect the SRS floor harness 28P connector (A)
from the SRS floor subharness C852.
15. Check resistance between the No. 21 terminal of
the SRS floor harness 28P connector and body
ground, and between the No. 22 terminal and body
ground. There should be an open circuit, or at least
1 M
.
Short to ground in the SRS floor subharness
or left side wire harness; replace the faulty
harness.
Short to ground in the SRS floor harness;
replace the SRS floor harness.
Terminal side of male terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:39:27 61S0X050_230_0252
−
−
−
−
*01
01
02
S0X4ASIK791000R321XFAAT20
’03-04 Models
DTC 32-1x (32-10 to 32-19, 32-1A to 32-1F):
Special Tools Required
YES
NO
YES
NO
23-253
07XAZ-S1A0200
07SAZ-TB4011A
A
A
B
Open or Increased Resistance in Front
Passenger’s Side Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead E 07XAZ-S1A0200
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the right side wire harness 2P
connector (A) from the front passenger’s side
airbag.
5. Connect the special tool (2
connector) to the
right side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-38).
Go to step 9.
Open or increased resistance in the front
passenger’s side airbag inflator, replace the front
passenger’s side airbag (see page 23-372).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect both seat belt tensioner 2P connectors
from the side wire harness (A).
11. Disconnect SRS unit connector B (28P) from the
from the right side wire harness 2P connector.
(cont’d)
Does the SRS indicator stay on?
Is DT C 32-1x indicated?
03/07/29 10:39:28 61S0X050_230_0253
SRS unit. Do not disconnect the special tool
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст