Honda Odyssey 2004. Manual — part 379
01
S0X4A00J18573958301KBAT00
01
02
S0X4A00J18573958351KBAT00
20-158
20-158
Openers
Tailgate Latch Replacement
Tailgate Lock Cylinder Replacement
Fastener Locations
: Bolt, 3
6 x 1.0 mm
9.8 N·m (1.0 kgf·m,
7.2 lbf·ft)
D
A
F
C
B
E
A
B
Fastener Location
: Bolt, 1
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
NOTE: Put on gloves to protect your hands.
1. Remove the tailgate trim panel (see page 20-61).
2. Disconnect the handle cable (A), cylinder rod (B),
lock rod (C) and tailgate latch switch connector (D),
and detach the connector.
3. Remove the bolts, then pull the tailgate latch (E) out.
4. Disconnect the tailgate latch actuator connector (F),
then remove the tailgate latch.
5. Install the latch in the reverse order of removal, and
note these items:
• Make sure the connectors are plugged in
properly and the each rod is connected properly.
• Make sure the cable actuates the latch before you
close the tailgate.
• Make sure the tailgate opens properly and locks
securely.
NOTE: Put on gloves to protect your hands.
1. Remove the tailgate trim panel (see page 20-61).
2. Disconnect the cylinder rod (A) and lock cylinder
switch connector (B) (if applicable), then detach the
lock cylinder switch connector from the tailgate.
3. Remove the bolt securing the lock cylinder (A).
Then turn the tailgate lock cylinder 45°, and remove
it.
4. Install the lock cylinder in the reverse order of
removal, and note these items:
• Make sure the connector is plugged in properly.
• Make sure the tailgate opens properly and locks
securely.
• Check the operation of the tailgate lock cylinder.
03/07/29 10:04:12 61S0X050_200_0160
01
S0X4A00J26200055801KBAT00
20-159
Frame
Spare Tire Well Access Panel Replacement
SPARE TIRE WELL ACCESS PANEL
Fastener Locations
: Bolt, 2
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
SPARE TIRE WELL ACCESS PANEL
1. Remove the spare tire well access panel as shown.
2. Install the access panel in the reverse order of removal.
03/07/29 10:04:13 61S0X050_200_0161
*01
S0X4A00J20170757212KBAT00
Subframe Torque
20-160
Frame
Front Subframe Replacement
STEERING GEARBOX FRONT
STIFFENER
SPECIAL BOLT
14 x 1.5 mm
103 N·m (10.5 kgf·m, 76 lbf·ft)
SPECIAL BOLT
14 x 1.5 mm
103 N·m (10.5 kgf·m, 76 lbf·ft)
10 x 1.25 mm
54 N·m (6.0 kgf·m,
43 lbf·ft)
FRONT SUSPENSION
SUBFRAME
FRONT SUSPENSION
SUBFRAME DAMPER
STEERING GEARBOX
REAR STIFFENER
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
FRONT SUSPENSION
SUBFRAME
FRONT BRACKET
12 x 1.25 mm
74 N·m (7.5 kgf·m,
54 lbf·ft)
FRONT SUSPENSION
SUBFRAME
FRONT SUSPENSION
SUBFRAME
REAR BRACKET
12 x 1.25 mm
117 N·m
(11.9 kgf·m,
86.1 lbf·ft)
To body
To body
To body
To body
SUBFRAME
Reference hole alignment
REFERENCE HOLE
(Body side)
SCREWDRIVER or
TAPERED PUNCH
INSTALLATION
REFERENCE HOLE
(Subframe side)
INSTALLATION
REFERENCE HOLE
Bottom view
Forward
LOWER
INSULATOR
Bottom view
Forward
LOWER
INSULATOR
INSTALLATION
REFERENCE
HOLE
After removing the subframe mounting bolts and steering gearbox stiffener mounting bolts, be sure to replace them
with new ones.
Replace.
Replace.
Replace.
03/07/29 10:04:13 61S0X050_200_0162
*01
S0X4A00J20170757211KBAT00
Subframe Torque
20-161
Rear Subframe Replacement
REAR SUSPENSION
SUBFRAME
SPECIAL BOLTS
14 x 1.5 mm
94 N·m (9.6 kgf·m, 69 lbf·ft)
To body
REAR SUSPENSION
SUBFRAME
To body
INSTALLATION
REFERENCE HOLE
SUBFRAME
REFERENCE HOLE
(Body side)
SCREWDRIVER or
TAPERED PUNCH
INSTALLATION
REFERENCE HOLE
(Subframe side)
INSTALLATION
REFERENCE HOLE
Reference hole alignment
After removing the subframe mounting bolts, be sure to replace them with new ones.
Replace.
03/07/29 10:04:14 61S0X050_200_0163
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст