Honda Odyssey 2004. Manual — part 358
02
20-74
Dashboard
Dashboard Removal/Installation (cont’d)
Fastener Locations
: Harness clip and connector clip
B
A
B
E
D
H
D
C
B
A
A
B
H
B
C
N
O
P
E
Q
U
U
M
K
R
L
J
J
I
H
S
W
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
F
E
G
V
T
8. Disconnect the side wire harness connectors (A), engine compartment wire harness connectors (B), door wire
harness connectors (C), dashboard wire harness connectors (D), steering hanger beam wire harness connectors
(E), brake switch connectors (F), parking brake switch connector (G), SRS wire harness connector (H), mode motor
connector (I), ECM/PCM connector (’99-00 models) or connectors (’01-04 models) (J), PCM subharness connector
(K) (’99-00 models), evaporator temperature sensor connector (L), air mix control motor connector (M),
recirculation control motor connector (N), blower relay connector (O) power transistor connector (P), blower
motor connector (Q) and antenna lead (R). For ’00-04 models with navigation system: Disconnect the navigation
unit harness connector (S) and GPS antenna connector (T).
9. For ’00-04 models with navigation system: Pull the carpet back as necessary (see page 20-65), and remove the
harness cushions (U), then pull the GPS antenna harness (V) out.
10. Using a Torx, T30 bit, remove the ground bolt (W) at the SRS control unit.
11. Detach all of the harness and connector clips.
03/07/29 10:01:54 61S0X050_200_0076
05
20-75
Fastener Locations
: Bolt, 2
: Bolt, 7
A
B
C
: Bolt, 3
D
: Bolt, 2
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
C
C
G
C
A
B
B
B
B
B
B
B
D
D
A
G
E
G
F
G
12. Remove the bolts (A, B, C, D), and lift up on the dashboard (E) to release the dashboard and steering hanger beam
(F) from the guide pins (G).
13. Carefully remove the dashboard through the front door opening:
14. Install the dashboard in the reverse order of removal, and note these items:
• Make sure the dashboard fits onto the guide pins correctly.
• Before tightening the bolts, make sure the dashboard wire harness and steering hanger beam wire harness are
not pinched.
• Make sure the connectors are plugged in properly, and the antenna lead is connected properly.
• Reconnect the negative cable to battery.
• Enter the anti-theft code for the radio and the navigation system, then enter the customer’s radio station presets.
• Reset the clock.
• Do the PCM idle learn procedure (see page 11-202), and the power window control unit reset procedure (’03-04
models) (see page 22-200).
03/07/29 10:01:55 61S0X050_200_0077
01
02
S0X4A00J26220257121KBAT00
20-76
Dashboard
Steering Hanger Beam Replacement
Fastener Location
: Nut, 1
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
Fastener Locations
: Srew, 1
B
: Clip, 4
C
: Clip, 3
D
A
D
C
B
B
B
C
B
C
NOTE:
• Have an assistant help you when removing and
installing the steering hanger beam.
• Take care not to scratch the dashboard.
• Put on gloves to protect your hands.
1. Remove the dashboard (see page 20-73).
2. Remove the following parts from the dashboard:
• Instrument panel (see page 20-69)
• Gauge assembly (see page 22-100)
• Center lower console (see page 20-68)
• Audio unit (see page 22-159)
• Display unit (with navigation system) (see page
22-385)
3. From under the dashboard on the driver’s side,
remove the nut, and pull out the fuse/relay box (A).
4. Open the driver’s side door, and remove the
dashboard side cover (A).
–1 Remove the screw.
–2 Gently pull out along the rear edge to release
the clips (B, C).
–3 Gently pry out on the side cover to release the
clips (B) and the tabs (D), then remove the side
cover.
03/07/29 10:01:55 61S0X050_200_0078
01
20-77
Fastener Locations
: Harness clip and connector clip
F
6 x 1.0 mm
9.8 N·m (1.0 kgf·m,
7.2 lbf·ft)
F
6 x 1.0 mm
9.8 N·m (1.0 kgf·m,
7.2 lbf·ft)
A
C
B
A
B
G
E
F
6 x 1.0 mm
9.8 N·m (1.0 kgf·m,
7.2 lbf·ft)
D
A
A
A
A
A
B
A
5. Disconnect the dashboard wire harness connectors (A), SRS wire harness connector (B) cruise control connector
(C) and keyless entry control unit connector (D). Remove the data link connector (DLC) (E) from the steering
hanger beam.
6. Remove the ground bolts (F).
7. Detach all of the harness and connector clips. With navigation system, remove the GPS antenna harness (G) from
the steering hanger beam.
(cont’d)
03/07/29 10:01:56 61S0X050_200_0079
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст