Mitsubishi 380. Manual — part 571
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI)
13A-376
STEP 6. Measure the sensor supply voltage at ECU
connector B-20 by using engine ECU check harness
special tool MB992044.
(1) Disconnect the all ECU connectors and connect engine
ECU check harness special tool MB992044 between the
separated connectors.
(2) Disconnect the camshaft position sensor connector B-106.
(3) Turn the ignition switch to the "ON" position.
(4) Measure the voltage between terminal No. 38 and ground.
• Voltage should be between 4.9 and 5.1 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.9 and 5.1 volts?
YES : Go to Step 7.
NO : Go to Step 8.
STEP 7. Check harness connector B-20 at ECU for
damage.
Q: Is the harness connector in good condition?
YES : Repair harness wire between camshaft position
sensor connector B-106 (terminal No. 2) and ECU
connector B-22 (terminal No. 38) because of open
circuit. Then go to Step 20.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 20.
16DB400A
COVER
ENGINE
CONTROL
UNIT
AIR
CLEANER
03DB191A
B-20 HARNESS
CONNECTOR
16DB400A
COVER
ENGINE
CONTROL
UNIT
AIR
CLEANER
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI)
13A-377
STEP 8. Check harness connector B-20 at ECU for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 9.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 20.
STEP 9. Check for short circuit to ground between
camshaft position sensor connector B-106 (terminal No. 2)
and ECU connector B-20 (terminal No. 38).
Q: Is the harness wire in good condition?
YES : Then go to Step 10.
NO : Repair it. Then go to Step 20.
16DB400A
COVER
ENGINE
CONTROL
UNIT
AIR
CLEANER
1
2
3
AK303130
HARNESS
CONNECTOR:
COMPONENT SIDE
AB
CAMSHAFT POSITION
SENSOR
B-106 (B)
CONNECTOR: B-106
16DB400A
COVER
ENGINE
CONTROL
UNIT
AIR
CLEANER
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI)
13A-378
STEP 10. Measure the power supply voltage at camshaft
position sensor connector B-106.
(1) Disconnect the connector B-106 and measure at the
harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 3 and ground.
• Voltage should be approximately 4.9 - 5.1 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage approximately between 4.9 - 5.1volts?
YES : Go to Step 12.
NO : Go to Step 11.
STEP 11. Check ECU harness connector B-20 for damage.
Q: Is the harness connector in good condition?
YES : Repair harness wire between ECU connector B-20
(terminal No. 25) and camshaft position sensor
connector B-106 (terminal No. 01) because of open
circuit or short circuit to ground. Then go to Step 20.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 20.
1
2
3
AK303130
HARNESS
CONNECTOR:
COMPONENT SIDE
AB
CAMSHAFT POSITION
SENSOR
B-106 (B)
CONNECTOR: B-106
AK303134
B-106 HARNESS
CONNECTOR:
COMPONENT SIDE
3 2 1
AB
16DB400A
COVER
ENGINE
CONTROL
UNIT
AIR
CLEANER
MULTIPORT FUEL INJECTION (MPI) DIAGNOSIS
MULTIPORT FUEL INJECTION (MPI)
13A-379
STEP 12. Check the continuity at camshaft position sensor
connector B-106.
(1) Disconnect the connector B-106 and measure at the
harness side.
(2) Check for the continuity between terminal No. 03 and
ground.
• Should be less than 2 ohms.
Q: Does continuity exist?
YES : Go to Step 15.
NO : Go to Step 13.
STEP 13. Check harness connector B-20 at ECU for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 14.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 20.
1
2
3
AK303130
HARNESS
CONNECTOR:
COMPONENT SIDE
AB
CAMSHAFT POSITION
SENSOR
B-106 (B)
CONNECTOR: B-106
03DB192A
B-106 HARNESS
CONNECTOR:
COMPONENT SIDE
1
2
3
16DB400A
COVER
ENGINE
CONTROL
UNIT
AIR
CLEANER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст