Mitsubishi Outlander (2003+). Manual — part 314
DOOR
BODY
42-31
DOOR GLASS AND REGULATOR
REMOVAL AND INSTALLATION
M1429001300393
Pre-removal Operation
•
Door Trim Assembly Removal (Refer to GROUP 52A,
Door Trim
•
Waterproof Film Removal (Refer to
).
Post-installation Operation
•
Door Window Glass Adjustment (Refer to
•
Waterproof Film Installation (Refer to
•
Door Trim Assembly Installation (Refer to GROUP 52A,
Door Trim
AC300452
AC101370
AB
<Front door>
<Rear door>
3
2
4
1
2
3
4
Power window switch removal steps
>>B<<
•
Post-installation operation check
1. Power window switch (Refer to
GROUP 52A, Door trim
Door window regulator assembly
removal steps
>>B<<
•
Post-installation operation check
<<A>> >>A<<
2. Window regulator assembly
<<A>>
3. Power window motor assembly
DOOR
BODY
42-32
REMOVAL SERVICE POINT
<<A>> WINDOW REGULATOR
ASSEMBLY/POWER WINDOW MOTOR
ASSEMBLY REMOVAL
1. Remove the door window glass installation bolts.
CAUTION
If tinting film is adhered to the door window
glass, attach special tool window glass holder
MB990480 to the outside of the glass to prevent
the film from peeling off.
2. Lift the door window glass, and attach special tool
window glass holder MB990480 to the glass as
shown to prevent the glass from falling.
3. Remove the window regulator assembly and
power window motor assembly.
INSTALLATION SERVICE POINTS
>>A<< WINDOW REGULATOR ASSEMBLY
INSTALLATION
When installing the window regulator assembly,
tighten the bolts to the specified torque in the order
shown.
>>B<< Post-installation operation check
When the following procedures are carried out, make
the power window switch learn the fully closed
position of the power window. (Refer to
).
•
Power window regulator removal or replacement
•
Power window switch removal or replacement
INSPECTION
M1429001400260
How to make the power window switch
learn the fully closed position of the
power window
How to make the power window switch learn the
fully closed position when the power window
switch is removed, or the power window
regulator assembly is removed or replaced
1. If the anti-trap function (safety mechanism) is
activated consecutively three times or more, the
fully closed position that the power window switch
has learned will be erased (initialized).
2. Operate the power window switch and fully open
the door window glass.
Door window glass removal steps
•
Window glass runchannel <Rear
door> (Refer to
•
Lower sash <Rear door> (Refer to
).
•
Door latch assembly <Rear door>
(Refer to
•
Door beltline moulding (Refer to
).
•
Door beltline inner weatherstrip
(Refer to
4. Door window glass
AC100009AB
MB990480
AC102851AC
<Rear door>
1
2
3
4
5
6
7
1
2
3
4
5
6
<Front door>
DOOR
BODY
42-33
CAUTION
The anti-trap function does not work until the
power window switch completes learning the
fully closed position (It is because the anti-trap
function is reset).
3. Operate the power window switch and fully close
the door window glass. The power window
activates for 0.7 seconds and stops automatically
when the power window switch is pressed once.
Repeat this operation until the door window glass
fully closes and release the switch once. Then,
hold the power window switch to the fully closed
side again for one second so that the power
window switch completes learning the fully closed
position.
NOTE: If the power window switch is operated to
open the door window glass while the switch is
learning, learning will be cancelled. If this
happens, return to step 2.
How to make the power window switch learn the
fully closed position when the power window
switch is replaced with a new one
CAUTION
The anti-trap function does not work until the
power window switch completes learning the
fully closed position (It is because the anti-trap
function is reset).
Operate the power window main switch to fully close
the door window glass by one-shot up action so that
the power window switch will complete learning
(Initialization is not needed).
NOTE: When the power window sub switch of each
seat is replaced, operate the power window main
switch to fully close the applicable power window by
one-shot up action (It is because the power window
sub switch does not have one-shot up/down
function).
DOOR
BODY
42-34
DOOR HANDLE AND LATCH
REMOVAL AND INSTALLATION
M1423004600306
Pre-removal Operation
•
Door Trim Assembly Removal (Refer to GROUP 52A
Door Trim
Post-installation Operation
•
Door Inside Handle Play Check (Refer to
•
Door Outside Handle Play Check (Refer to
•
Door Trim Assembly Installation (Refer to GROUP 52A,
Door Trim
AC101531AD
9.0 ± 2.0 N·m
9.0 ± 2.0 N·m
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
<Front door>
<Rear door>
1
2
4
3
5
9
8
1
2
9
3
5
6
7
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
8
Door handle and door latch assembly
removal steps
>>C<<
1. Door inside handle
•
Waterproof film (Refer to
).
>>B<<
2. Lower sash
3. Door outside handle
4. Door lock key cylinder
5. Door latch assembly
6. Inside lock cable
7. Inside lock rod
8. Inside handle rod
Door check removal steps
•
Waterproof film (Refer to
>>A<<
9. Door check
Door handle and door latch assembly
removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст