Mitsubishi Outlander (2003+). Manual — part 313
DOOR
BODY
42-27
POWER WINDOW OPERATING CURRENT
CHECK
M1429001100247
1. Remove the power window fuse and connect an
ammeter as shown in the illustration.
2. When the power window switch is pressed to the
“UP” position, a large amount of current flows at
the time the window starts to close and when it is
fully closed, so measure the operation current in
the interval between these two points.
Standard value: 5
±
1A (Power supply
voltage 14.5
±
0.5V, 25
°
C)
3. If the operation current is outside the standard
value, refer to
.
POWER WINDOW RELAY CHECK
M1429001800235
CIRCUIT BREAKER (INCORPORATED IN
THE POWER WINDOW MOTOR)
INSPECTION
M1429001700108
1. Pull the power window switch to the UP position
to fully close the door window glass, and keep
pulling the switch for 10 additional seconds.
2. Release the power window switch from the UP
position and immediately press it to the DOWN
position. The condition of the circuit breaker is
good if the door window glass starts to move
downwards within 60 seconds.
POWER WINDOW CHECK
M1429004400269
Check the system as described below. If the system
does not work, carry out troubleshooting. Refer to
GROUP 54B, Troubleshooting
or GROUP
54C, Troubleshooting
•
Operate the power window switch of each seat to
check that the power window works.
•
Turn on the power window lock switch of the
power window main switch, and operate the front
passenger's and rear power window sub switches
to check that the power windows do not work.
•
Turn on the power window lock switch of the
power window main switch, and operate the
power window main switch to check that each
power window operates.
AC208065AC
AC300331
AC106844
1 2 3
4
5
1
3
4
5
AC207981
AB
Junction block
Power window relay
BATTERY
VOLTAGE
TESTER
CONNECTION
SPECIFIED
CONDITION
Not applied
4
−
5
Open circuit
•
Connect
terminal No.1
and the positive
battery
terminal.
•
Connect
terminal No.3
and the
negative
battery
terminal.
4
−
5
Less than 2
ohms
DOOR
BODY
42-28
CENTRAL DOOR LOCKING SYSTEM
INSPECTION
M1427001100199
Check that the central door locking system works by
operating the key cylinder and the inside lock knob
(driver's door). Carry out troubleshooting if the
system does not activate. Refer to GROUP 54B,
Troubleshooting
, refer to GROUP 54C,
Troubleshooting
.
DOOR OUTSIDE HANDLE PLAY CHECK
M1423001600255
1. Check that the door outside handle play is within
the standard value range.
Standard value (A):
Front door: 2.6
±
2.5 mm
Rear door: 1.3
±
1.3 mm
2. If the door outside handle play is not within the
standard value range, check the door outside
handle or the door latch assembly. Replace if
necessary.
DOOR INSIDE HANDLE PLAY
ADJUSTMENT
M1423001500270
1. Check that the door inside handle play is within
the standard value range.
Standard value (B):
Front door: 10.4
±
9.6 mm
Rear door: 10
±
9.6 mm
2. If the door inside handle play is outside the
standard value range.
3. Remove the door trim assembly (Refer to GROUP
52A, Door trim
4. Remove the waterproof film (Refer to
5. Adjust the door inside handle play with the outer
cable end connecting the door inside handle and
inside lock cable.
AC006113AB
A
AC006114
Y0705AU
AB
A
A
B
Section A – A
AC100404 AB
Clip
Inner cable
Outer cable end
Inside handle rod
Door inside handle
DOOR
BODY
42-29
DOOR ASSEMBLY
REMOVAL AND INSTALLATION
M1423002200261
Post-installation Operation
•
AC103073 AC
<Front door>
<Rear door>
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
1
1.5 ± 0.5 N·m
1.5 ± 0.5 N·m
9.0 ± 2.0 N·m
11 ± 2 N·m
11 ± 2 N·m
9.0 ± 2.0 N·m
21 ± 4 N·m
27 ± 5 N·m
21 ± 4 N·m
27 ± 5 N·m
21 ± 4 N·m
27 ± 5 N·m
21 ± 4 N·m
27 ± 5 N·m
5, 6
Removal
1. Damper
Door assembly removal steps
•
Scuff Plate and Cowl Side Trim (Refer
to GROUP 52A, Trims
).
2. Harness connector
3. Door check connecting bolt
4. Door assembly
5. Door upper hinge
6. Door lower hinge
Striker removal steps
>>A<<
7. Striker
8. Striker shim
Door switch removal
9. Door switch
Door assembly removal steps
DOOR
BODY
42-30
INSTALLATION SERVICE POINT
>>A<< STRIKER INSTALLATION
Align the centre of the striker and latch within
±
1.5
mm, and install.
INSPECTION
M1423006000300
DOOR SWITCH CHECK
AC006126AB
Striker center
Striker
Latch center
Latch
+1.5 mm
-1.5 mm
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
Released (ON) 1
−
switch body,
2
−
switch body,
3
−
switch body
Less than 2
ohms
Depressed
(OFF)
1
−
switch body,
2
−
switch body,
3
−
switch body
Open circuit
AC211414
1
2
3
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст