Mitsubishi Outlander (2003+). Manual — part 210

TROUBLESHOOTING <A/T>

AUTOMATIC TRANSMISSION (FF)

23A-135

ACTUATOR TEST JUDGMENT VALUE

M1231008200345

68

Upshift switch

Ignition switch: ON
Engine: Stopped

Selector lever position: D

OFF

Selector lever position:
Select sport mode

OFF

Selector lever position:
Upshift and hold the
selector lever

ON

Selector lever position:
Downshift and hold the
selector lever

OFF

69

Downshift switch

Ignition switch: ON
Engine: Stopped

Selector lever position: D

OFF

Selector lever position:
Select sport mode

OFF

Selector lever position:
Upshift and hold the
selector lever

OFF

Selector lever position:
Downshift and hold the
selector lever

ON

Data list
No.

Check item

Inspection conditions

Normal condition

Item No.

Inspection item

Test description

Inspection
condition

Normal status

01

LR solenoid valve

Actuate solenoid valve
indicated by MUT-II/III
for 5 seconds at duty
ratio of 50%.
Other remaining
solenoid valve are not
ON.

Ignition switch: ON
Selector lever
position: P
Engine: Stopped
Accelerator pedal:
Released

When solenoid valve is
actuated, operating
sound is audible.

02

UD solenoid valve

03

2ND solenoid valve

04

OD solenoid valve

06

DCC solenoid valve

07

1st indicator lamp

Illuminate shift
indicator indicated by
MUT-II/III for 3
seconds

Shift indicator is
displayed.

08

2nd indicator lamp

09

3rd indicator lamp

10

4th indicator lamp

12

A/T control relay

A/T control relay is
OFF for three
seconds.

Data list No.54
During test: 0 V
Normal: System voltage
(V)

TROUBLESHOOTING <A/T>

AUTOMATIC TRANSMISSION (FF)

23A-136

INVECS-II CANCEL COMMAND

M1231009500327

CHECK AT ENGINE-A/T-ECU TERMINALS

M1231008400350

Item No.

Item

Contents

NOTE

14

INVECS-II

Stop the INVECS-II control and
changes gear according to the
standard shift pattern.

Use this procedure when carrying out road
test procedure 8.
If the ignition switch is turned from OFF to
ON to OFF, this function restores the
INVECS-II control.

AC201888

1

2

3

4

5

6

7

8

9 10

12

11

13

14

15

16 17 18

19 20

21

22

23 24 25

26 27

31 32

33

34

35 36 37 38 39 40 41 42

43

44 45 46 47 48

50

51

52 53

54 55

49

56

57

58

61 62

63 64

65 66 67 68 69 70 71 72 73

74 75 76 77 78 79 80 81 82

83 84

85 86 87

88 89

91 92

93 94 95

96 97 98 99 100101102103

104

105106

107108109

110111112

113114

115116117

118119120

121122

123 124

125126127128129 130 131 132 133

134135

136137 138 139 140 141

142143

144

145 146

C-139

C-140

C-141

C-142

C-138

AI

Terminal
No.

Check item

Inspection condition

Standard value

39

Stoplight switch

•

Ignition switch: ON

•

Brake pedal: Depressed

System voltage

•

Ignition switch: ON

•

Brake pedal: Released

1 V or less

64

Input shaft speed
sensor

•

Measure between terminals 64 and 88
with an oscilloscope.

•

Engine: 2,000 r/min

•

Selector lever position: Sport mode
(3rd gear)

Refer to

P.23A-139

,

Inspection Procedure
Using an Oscilloscope.

66

Inhibitor awitch: P

•

Ignition switch: ON

•

Selector lever position: P

System voltage

•

Ignition switch: ON

•

Selector lever position: Other than
above

1 V or less

67

Inhibitor awitch: R

•

Ignition switch: ON

•

Selector lever position: R

System voltage

•

Ignition switch: ON

•

Selector lever position: Other than
above

1 V or less

68

Shift switch (Down)

•

Ignition switch: ON

•

Selector lever operation: Downshift and
hold the selector lever

System voltage

•

Ignition switch: ON

•

Selector lever operation: Other than
above

1 V or less

70

Crankshaft position
sensor

Engine: Idling

1.5

−

2.5 V

TROUBLESHOOTING <A/T>

AUTOMATIC TRANSMISSION (FF)

23A-137

73

Output shaft speed
sensor

•

Measure between terminals 73 and 88
with an oscilloscope.

•

Engine: 2,000 r/min

•

Selector lever position: Sport mode
(3rd gear)

Refer to

P.23A-139

,

Inspection Procedure
Using an Oscilloscope.

75

Inhibitor awitch: N

•

Ignition switch: ON

•

Selector lever position: N

System voltage

•

Ignition switch: ON

•

Selector lever position: Other than
above

1 V or less

76

Inhibitor switch: D

•

Ignition switch: ON

•

Selector lever position: D

System voltage

•

Ignition switch: ON

•

Selector lever position: Other than
above

1 V or less

77

Shift switch (Up)

•

Ignition switch: ON

•

Selector lever operation: Upshift and
hold the selector lever

System voltage

•

Ignition switch: ON

•

Selector lever operation: Other than
above

1 V or less

79

Vehicle speed signal

•

Measure between terminals 79 and
ground with an oscilloscope.

•

Engine: 2,000 r/min

•

Selector lever position: Sport mode
(3rd gear)

Refer to

P.23A-139

,

Inspection Procedure
Using an Oscilloscope.

85

Select switch

•

Ignition switch: ON

•

Selector lever position: Sport mode

System voltage

•

Ignition switch: ON

•

Selector lever position: Other than
above

1 V or less

119

A/T fluid temperature
sensor

A/T fluid temperature: 20

°

C

3.8

−

4.0 V

A/T fluid temperature: 40

°

C

3.2

−

3.4 V

A/T fluid temperature: 80

°

C

1.7

−

1.9 V

121

Shift indicator C

Measure the voltage when
each shift range is displayed
by using actuator function
(item No.07 to 10) on the
scan tool (MUT-II/III).

1st

1 V or less

2nd

1 V or less

3rd

1 V or less

4th

8

−

10 V

123

Solenoid valve power
supply

Ignition switch: LOCK (OFF)

1 V or less

Ignition switch: ON

System voltage

124

Solenoid valve power
supply

Ignition switch: LOCK (OFF)

1 V or less

Ignition switch: ON

System voltage

Terminal
No.

Check item

Inspection condition

Standard value

TROUBLESHOOTING <A/T>

AUTOMATIC TRANSMISSION (FF)

23A-138

125

Shift indicator B

Measure the voltage when
each shift range is displayed
by using actuator function
(item No.07 to 10) on the
scan tool (MUT-II/III).

1st

1 V or less

2nd

8

−

10 V

3rd

8

−

10 V

4th

1 V or less

127

A/T control relay

Always

1 V or less

128

LR solenoid valve

•

Engine: Idling

•

Selector lever position: P

System voltage

•

Engine: Idling

•

Selector lever position: Sport mode
(2nd gear)

6

−

9 V

130

DCC clutch solenoid
valve

•

Engine: Idling

•

Selector lever position: P

System voltage

131

Ground

Always

1 V or less

134

Shift indicator A

Measure the voltage when
each shift range is displayed
by using actuator function
(item No.07 to 10) on the
scan tool (MUT-II/III).

1st

8

−

10 V

2nd

1 V or less

3rd

8

−

10 V

4th

1 V or less

135

A/T fluid temperature
warning light

Ignition switch: LOCK (OFF) to ON

1 V or less to System
voltage (after several
seconds have elapsed)

136

2ND solenoid valve

•

Engine: Idling

•

Selector lever position: Sport mode
(2nd gear)

System voltage

•

Engine: Idling

•

Selector lever position: P

6

−

9 V

137

UD solenoid valve

•

Engine: Idling

•

Selector lever position: Sport mode
(1st gear)

System voltage

•

Engine: Idling

•

Selector lever position: P

6

−

9 V

138

OD solenoid valve

•

Engine: Idling

•

Selector lever position: Sport mode
(3rd gear)

System voltage

•

Engine: Idling

•

Selector lever position: P

6

−

9 V

139

Ground

Always

1 V or less

Terminal
No.

Check item

Inspection condition

Standard value