Mitsubishi Outlander (2003+). Manual — part 225
SPECIAL TOOLS
FRONT AXLE
26-5
MB991056 or
MB991355
Knuckle arm
bridge
•
Removal of the hub
•
Removal of the wheel bearing
MB991721
Sliding hammer
Removal of the output shaft <4WD>
A: MB991017
B: MB990998
C: MB991000
A, B: Front hub
remover and
installer
C: Spacer
•
Removal of the hub
•
Provisional holding of the wheel
bearing
•
Measurement of hub starting torque
•
Measurement of wheel bearing axial
play
NOTE: MB991000, which belongs to
MB990998, should be used as a
spacer.
MB990685
Torque wrench
Measurement of hub starting torque
MB990326 Preload
socket
MB990810
Side bearing
puller
•
Removal of the centre bearing
bracket
•
Removal of the wheel bearing inner
race (outside)
MB991172
Inner shaft
installer base
Press-fitting of the inner shaft
Tool
Number
Name
Use
AC100320AB
A
B
C
MB990326
MB990810
SPECIAL TOOLS
FRONT AXLE
26-6
MB991248 or
MB998801
Inner shaft
remover
Removal of the inner shaft
MB991460
Plug
Prevention of transmission fluid drain
and of entry of foreign objects
MB991561
Boot band
crimping tool
BJ boot (resin boot) band installation
MB990925
Bearing and oil
seal installer set
•
Removal of the wheel bearing
•
Removal and installation of the
centre bearing
•
Press-fitting of the dust seal outer,
inner
MB990890
Rear suspension
bushing base
•
Installation of the wheel bearing
•
Press-fitting of the dust seal outer,
inner
MB990883
Rear suspension
bushing arbor
Installation of the wheel bearing
Tool
Number
Name
Use
MB991248
MB991561
MB990925
MB990890
MB990883
SPECIAL TOOLS
FRONT AXLE
26-7
Tool
Type
Tool number
O D mm
A
MB990926
39.0
MB990927
45.0
MB990928
49.5
MB990929
51.0
MB990930
54.0
MB990931
57.0
MB990932
61.0
MB990933
63.5
MB990934
67.5
MB990935
71.5
MB990936
75.5
MB990937
79.0
B
MB990938
−
C
MB990939
−
ACX02372
A
B
C
Brass bar
Bar (snap-in type)
Tool box
MB990925
AC
Installer adapter
ON-VEHICLE SERVICE
FRONT AXLE
26-8
ON-VEHICLE SERVICE
WHEEL BEARING AXIAL PLAY CHECK
M1261000900213
1. Remove the caliper assembly and suspend it with
a wire.
2. Remove the brake disc from the front hub.
3. Attach a dial gauge as shown in the illustration,
and then measure the axial play while moving the
hub in the axial direction.
Limit: 0.05 mm
4. If axial play exceeds the limit, disassemble the
front hub assembly and check the parts.
5. Install the brake disc, caliper assembly and
tighten the caliper assembly mounting bolts to the
specified torque 100
±
10 N
⋅
m.
HUB BOLT REPLACEMENT
M1261001000279
1. Remove the caliper assembly and suspend it with
wire so that it does not fall.
2. Remove the brake disc.
3. Use the following special tools to remove the hub
bolts.
•
End yoke holder (MB990767)
•
Hub bolt remover (MB991618)
4. Install the plain washer to the new hub bolt, and
install the bolt with a nut.
5. Install the brake disc, caliper assembly and
tighten the caliper assembly mounting bolts to the
specified torque 100
±
10 N
⋅
m.
AC102438
AC102439 AC
MB990767
MB991618
AC102440
MB990767
Plain
washer
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст