Mitsubishi Outlander (2003+). Manual — part 224
26-1
GROUP 26
FRONT AXLE
CONTENTS
GENERAL INFORMATION . . . . . . . .
SERVICE SPECIFICATIONS. . . . . . .
LUBRICANTS . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS. . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE. . . . . . . . . . .
WHEEL BEARING AXIAL PLAY CHECK . .
HUB BOLT REPLACEMENT . . . . . . . . . . .
FRONT AXLE HUB ASSEMBLY . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
DISASSEMBLY AND REASSEMBLY . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
DRIVE SHAFT ASSEMBLY . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
DISASSEMBLY AND REASSEMBLY . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
GENERAL INFORMATION
FRONT AXLE
26-2
GENERAL INFORMATION
M1261000100392
The front axle consists of front hubs, knuckles, wheel
bearings and drive shafts, and it has the following
features:
•
The wheel bearing is a double-row angular
contact ball bearing which incorporates the oil
seals and is highly resistant to a thrust load.
•
The driveshaft incorporates BJ-PTJ type constant
velocity joints with high transmission efficiency for
low vibration and noise.
•
The dynamic damper has been mounted on the
left driveshaft <2WD, 4WD> and on the right
driveshaft <4WD> to reduce differential gear
noise.
•
Due to the use of the inner shaft and bracket
assembly, the right and left drive shafts are
approximately the same in length. This reduces
noise, vibration and torque steer.<2WD>
•
Due to the use of the output shaft, the right and
left drive shafts are approximately the same in
length. This reduces noise, vibration and torque
steer.<4WD>
•
ABS rotor for detecting the wheel speed is
press-fitted to the BJ outer wheel.
NOTE:
.
•
PTJ: Pillow Tripod Joint
•
BJ: Birfield Joint
SPECIFICATIONS
CONSTRUCTION DIAGRAM
Item
2WD
4WD
Wheel bearing Type
Double-row angular contact ball bearing
Bearing (OD x ID) mm
80 x 40
80 x 40
Driveshaft
Joint type
Outer
BJ
BJ
Inner
PTJ
PTJ
Length (joint to joint)
×
diameter mm
LH 383.5
×
24
361
×
22
RH
474.5
×
24
455
×
22
AC106952
Front hub
Knuckle
Strut assembly
PTJ (LH)
Drive shaft (LH)
Dynamic damper
(LH only)
BJ
Wheel bearing
Bracket assembly
Drive shaft (RH)
PTJ (RH)
Inner shaft
AD
<2WD>
ABS rotor
SERVICE SPECIFICATIONS
FRONT AXLE
26-3
SERVICE SPECIFICATIONS
M1261000300352
AC308113
Front hub
Knuckle
Strut assembly
PTJ (LH)
Drive shaft (LH)
Dynamic damper
(LH)
BJ
Wheel bearing
Drive shaft (RH)
PTJ (RH)
Output shaft
Output shaft
<4WD>
AB
ABS rotor
Dynamic damper
(RH)
Item
Standard value
Limit
Wheel bearing axial play mm
−
0.05
Hub starting torque N
⋅
m
−
1.8
Protruding length of stabilizer link mm
9.4
±
0.4
−
Setting of PTJ boot length mm 2WD
90
±
3
−
4WD
85
±
3
−
Opening dimension of the
special tool (MB991561) mm
When the BJ boot band
(small) is crimped
2.9
−
When the BJ boot band
(large) is crimped
2.9
−
Crimped width of the BJ boot band mm
2.4
−
2.8
−
LUBRICANTS
FRONT AXLE
26-4
LUBRICANTS
M1261000400445
SPECIAL TOOLS
M1261000600353
Item
Specified lubricant
Quantity
PTJ boot grease
Repair kit grease
2WD
215
±
10 g
4WD
150
±
10 g
BJ boot grease
Repair kit grease
2WD
120
±
10 g
4WD
85
±
10 g
Dust seal inner grease
Repair kit grease
14
−
20 g
Dust seal outer grease
Repair kit grease
8
−
12 g
Tool
Number
Name
Use
MB990767
End yoke holder
Fixing of the hub
MB991618
Hub bolt remover
Removal of the hub bolt
MB991897
Ball joint remover Knuckle and tie rod end ball joint
disconnection
NOTE: Steering linkage puller
(MB990635 or MB991113)is also used
to disconnect knuckle and tie rod end
ball joint.
MB990241
A: MB990242
B: MB990244
Axle shaft puller
A: Puller shaft
B: Puller bar
Removal of the drive shaft
MB991354
Puller body
B990767
MB991618
AC106827
MB990241AB
A
B
MB991354
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст