Mitsubishi Outlander (2003+). Manual — part 33
SEALANT
ENGINE LUBRICATION
12-3
SEALANT
M1121000500258
SPECIAL TOOLS
M1121000600363
ON-VEHICLE SERVICE
ENGINE OIL CHECK
M1121000900320
1. Pull out the level gauge slowly and check that the
oil level is in the illustrated range.
2. Check that the oil is not excessively dirty, that
there is no coolant or petrol mixed in, and that it
has sufficient viscosity.
ENGINE OIL REPLACEMENT
M1121001000494
1. Start the engine and allow it to warm up until the
temperature of the coolant reaches 80
°
C to 90
°
C.
2. Remove the engine oil filler cap.
CAUTION
Use care as oil could be hot.
3. Remove the drain plug to drain oil.
4. Install a new drain plug gasket so that it faces in
the direction shown in the illustration, and then
tighten the drain plug to the specified torque.
Tightening torque: 39
±
5 N
⋅
m
NOTE: Install the drain plug gasket so it faces in
the direction shown in the illustration.
Item
Specified sealant
Remark
Oil pressure switch
3M ATD Part No. 8660 or equivalent
Semi-drying sealant
Tool
Number
Name
Use
MB991610
Oil filter wrench
Removal and installation
of engine oil filter (When
using the oil filter of
MD356000)
MD998054
Oil pressure switch
wrench
Removal and installation
of oil pressure switch
MB991610
AC300837
Drain plug
gasket
Oil pan side
Oil pan
Drain plug
AB
ON-VEHICLE SERVICE
ENGINE LUBRICATION
12-4
5. Refill with specified quantity of oil.
Specified Engine Oil (ACEA and API
classification): ACEA A1, A2 or A3/API SG or
higher
Total quantity (Includes volume inside engine
oil filter):
4.3 L <4G63, 4G69 (A/T)>
4.6 L <4G69 (M/T)>
6. Install the engine oil filler cap.
7. Check oil level.
ENGINE OIL FILTER REPLACEMENT
M1121001100350
1. Start the engine and allow it to warm up until the
temperature of the coolant reaches 80
°
C to 90
°
C.
2. Remove the engine oil filler cap.
CAUTION
Use care as oil could be hot.
3. Remove the drain plug to drain oil.
4. Remove the under cover.
5. Use the respective tool in the following table to
remove the engine oil filter.
6. Clean the filter bracket side mounting surface.
7. Apply a small amount of engine oil to the O-ring of
the new oil filter.
8. Once the O-ring of the oil filter is touching the
flange, use the respective tool in the following
table to tighten to the specified torque.
9. Install the drain plug and refill the engine oil (Refer
to
10.Race the engine 2
−
3 times, and check to be sure
that no engine oil leaks from installation section of
the oil filter.
AC301513
AC000093
MB991610 or
commercially-
available tool
AH
AC103250AD
O-ring
Number
Special tool
Tightening torque
MD356000
Oil filter wrench (MB991610)
or equivalent
Approximately 3/4 turn (14
±
2 N
⋅
m)
MD136466,
MD322508
Commercially- available tool
Approximately 3/4 turn (17
±
3 N
⋅
m)
ON-VEHICLE SERVICE
ENGINE LUBRICATION
12-5
OIL PRESSURE CHECK
M1121002300432
1. Check engine oil quantity.
2. Remove the oil pressure switch terminal.
CAUTION
Since sealant is applied to the thread of oil
pressure switch, take care not to damage the oil
pressure switch when removing it.
3. Use the special tool Oil pressure switch wrench
(MD998054) to remove the oil pressure switch.
4. Install the oil pressure gauge.
NOTE: Use an adapter of PT 1/8 thread.
5. Run the engine to warm it.
6. After the engine has been warmed up, check that
oil pressure is within the standard value.
Standard value:
At idle: 29 kPa or more
At 3,500 r/min: 294
−
686 kPa
7. Remove the oil pressure gauge.
8. Apply the specified sealant to the thread of oil
pressure switch.
Specified sealant: 3M
ä ATD Part No. 8660 or
equivalent
CAUTION
Do not start the engine within one hour after the
oil pressure switch has been installed.
9. Use the special tool Oil pressure switch wrench
(MD998054) to tighten the oil pressure switch to
the specified torque.
Tightening torque: 19
±
3 N
⋅
m
10.Install the oil pressure switch terminal.
AK000197AF
Cylinder block
Oil pressure switch
AKX00294
MD998054
AD
AKX00295AD
AKX00294
MD998054
AD
ENGINE OIL COOLER
ENGINE LUBRICATION
12-6
ENGINE OIL COOLER
REMOVAL AND INSTALLATION
M1121001300116
Pre-removal Operation
•
Front Under Cover (LH) Removal (Refer to GROUP 51,
Under Cover
Post-installation Operation
•
Front Under Cover (LH) Installation (Refer to GROUP 51,
Under Cover
•
Engine Oil Refilling and Level Check (Refer to
).
AC309226
AB
24
18
N
12 ± 2 N·m
12 ± 2 N·m
5.0 ± 1.0 N·m
48 ± 7 N·m
23
N
48 ± 7 N·m
45 ± 5 N·m
12 ± 2 N·m
12 ± 2 N·m
12 ± 2 N·m
21
12 ± 2 N·m
45 ± 5 N·m
3
N
1
N
16
17
19
20
22
25
2
4
8
7
6
5
12 ± 2 N·m
12 ± 2 N·m
33 ± 2 N·m
4
N
15
14
12
11
13
26
27
9
10
9
10
Engine oil cooler removal steps
⋅•
Splash Shield Mounting Clips (LH)
(Refer to GROUP 51, Front Bumper
1. Eye bolt
2. Gasket
3. Eye bolt
4. Gasket
5. Engine oil cooler assembly
6. Bracket
7. Bracket
8. Engine oil cooler
9. Collar
10. Bush
Engine oil cooler hose removal
steps (Engine oil cooler side)
11. Engine oil cooler return hose
connection
1. Eye bolt
2. Gasket
12. Engine oil cooler return hose
13. Bolt
Engine oil cooler removal steps
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст