Mitsubishi Outlander (2003+). Manual — part 571
AUTOMATIC AIR CONDITIONER PANEL ASSEMBLY (A/C-ECU)
AUTOMATIC AIR CONDITIONER
55B-99
AUTOMATIC AIR CONDITIONER PANEL ASSEMBLY
(A/C-ECU)
REMOVAL AND INSTALLATION
M1554010900064
32
Input from the engine-A/T-ECU
(A/C2)
When the A/C is under low load
System voltage
33
Input from the compressor relay
Compressor: ON
System voltage
34
Input from the engine-A/T-ECU
(A/C1)
When the A/C is stopped
0 V
When the A/C is operating (When the
compressor is operating)
System voltage
35
-
-
-
36
ACC power supply
Ignition switch: ACC
System voltage
Terminal
No.
Check items
Check conditions
Normal
conditions
AC301496
1
2
3
5
4
AB
Removal steps
•
Centre panel(Refer to GROUP
52A, Instrument Panel
<LHD>
or Instrument
Panel <RHD>
1.
Knob
2.
Panel
3.
Rear defogger knob
4.
Outside/inside air selection knob
5.
Automatic air conditioner control
panel (A/C-ECU)
Removal steps (Continued)
HEATER UNIT
AUTOMATIC AIR CONDITIONER
55B-100
HEATER UNIT
REMOVAL AND INSTALLATION
M1554009100097
Refer to GROUP 55A, Heater Unit Blower assembly
.
DISASSEMBLY AND REASSEMBLY
M1554009200072
AC301506AB
11
2
N
9
8
6
7
12
1
5
4
14
10
13
3
Disassembly steps
1.
Evaporator cover
2.
Heater core
3.
Expansion valve
4.
Joint
5.
Evaporator
6.
O ring
7.
Air thermo sensor
8.
Heater water temperature sensor
9.
Aspirator hose
10. Aspirator
11. Wiring harness
12. Mode selection damper control
motor and potentiometer
13. Air mixing damper control motor
and potentiometer
14. Heater case
Disassembly steps (Continued)
AIR MIXING DOOR MOTOR, AIR OUTLET CHANGEOVER DAMPER MOTOR AND BLOWER MOTOR
AUTOMATIC AIR CONDITIONER
55B-101
AIR MIXING DOOR MOTOR, AIR OUTLET CHANGEOVER
DAMPER MOTOR AND BLOWER MOTOR
REMOVAL AND INSTALLATION
M1554011100050
AC301512
1
2
3
AB
Air mixing damper control motor
and potentiometer removal
steps
•
Foot duct <driver's side>
1.
Air mixing damper control motor
and potentiometer
Mode selection damper control
motor and potentiometer
removal steps
2.
Mode selection damper control
motor and potentiometer
Blower motor removal steps
3.
Blower motor
AIR MIXING DOOR MOTOR, AIR OUTLET CHANGEOVER DAMPER MOTOR AND BLOWER MOTOR
AUTOMATIC AIR CONDITIONER
55B-102
INSPECTION
M1552014301287
CHECK THE AIR MIXING DAMPER
CONTROL MOTOR AND
POTENTIOMETER
Check the air mixing damper control motor
Potentiometer check
When the resistances between terminals 2 and 5 as
well as terminals 5 and 6 are measured at the air
mixing damper motor check, the resistance value
should change gradually within the standard value.
Standard value: Approximately 0.65
−
5.35
k
Ω
MODE SELECTION DAMPER CONTROL
MOTOR AND POTENTIOMETER CHECK
Mode selection damper control motor check
Potentiometer check
When the resistances between terminals 2 and 5 as
well as terminals 5 and 6 are measured at the mode
selection damper control motor check, the resistance
value should change gradually within the standard
value.
Standard value: Approximately 0.65
−
5.35
k
Ω
BLOWER MOTOR CHECK
Execute actuator test item No.01 to 04 by using
MUT-II with the vehicle body, and check that the
blower motor works normally. (Refer to
Battery
connection
(+) terminal
Battery
connection
(-) terminal
Lever operation
1
3
Rotate to the HOT
position.
3
1
Rotate to the COOL
position.
AC301517
MAX. COOL
position
MAX HOT position
AC
Battery
connection
(+) terminal
Battery
connection
(-) terminal
Lever operation
1
3
Rotate to the DEF
position.
3
1
Rotate to the FACE
position.
AC301519AC
DEF position
FACE
position
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст