Mitsubishi Outlander (2003+). Manual — part 341
INSTRUMENT PANEL ASSEMBLY
INTERIOR
52A-3
CAUTION
•
Refer to GROUP 52B-SRS Service Precautions
and Air bag Module and Clock Spring
before removing the passenger side air bag module.
•
Do not subject the SRS-ECU to any shocks when removing or installing the instrument panel.
Pre-removal and Post-installation Operation
•
Removal and Installation of Front Floor Console (Refer to
•
Removal and Installation of Steering Wheel (Refer to
GROUP 37A, Steering Wheel
) and Air Bag
Module Assembly (Refer to GROUP 52B, Air Bag Module
and Clock Spring
AC301272
5
6
4
12
25
10
8
9
11
15
7
19
18
20
21
17
14
13
16
22
2
1
3
2
25
24
23
c
d
d
j
44 ± 10 N·m
e
d
c f
d
a
a
b
g
h
g
b
44 ± 10 N·m
j
d
d
d
AB
N
26
Removal steps
1.
Instrument panel clock garnish
<<A>>
2.
Instrument panel air outlet (centre)
3.
Clock
4.
Instrument panel driver’s side
garnish
5.
Meter bezel
6.
Combination meter
7.
Junction block cover
•
Hood lock release handle (Refer to
GROUP 42, Hood
8.
Instrument panel parcel box
•
Floor harness (R.H.) and junction
block connection
9.
Instrument lower panel
<<A>>
10. Instrument panel air outlet (L.H.)
11. Instrument lower panel bracket
12. Column cover
Removal steps (Continued)
INSTRUMENT PANEL ASSEMBLY
INTERIOR
52A-4
•
Air mix door cable, blow vent
changeover damper cable
connection (Refer to GROUP 55A,
Heater Control Assembly and A/C
Switch
13. Knob
>>A<<
14. Centre panel
15. Centre panel assembly
16. Manual air conditioner control panel
17. Radio plug
18. Centre lower panel
19. Centre lower box
20. Centre lower cover
•
Front scuff plate, cowl side trim
(Refer to
21. Back bone spacer
22. Glove box stopper
23. Glove box
24. Connector block
25. Instrument panel side cover
•
Roof harness connection
•
Instrument panel harness earth
connection
•
Instrument panel and body harness
connection
•
Steering shaft harness connector
and clamp
•
Stop lamp switch harness
connector
•
SRS-ECU harness connector
•
Shift lock cable clamp
•
Steering shaft installation bolt
(Refer to GROUP 37A, Steering
Shaft
26. Instrument panel assembly
Removal steps (Continued)
INSTRUMENT PANEL ASSEMBLY
INTERIOR
52A-5
CLIP AND CLAW POSITIONS
AC301617
NOTE
(1) : Clip position
(2) : Claw position
Section A – A
A
A
B
B
E
E
H
I
I
H
K
D
D
C
C
J
J
G
F
F
G
K
H
H
Section B – B
Section C – C
Section D – D
Section E – E
Section F – F
Section G – G
Section H – H
Section I – I
Section J – J
Section K – K
Instrument
panel side
cover
Clip
Instrument panel
assembly
Instrument panel
assembly
Claw
Instrument panel
side cover
Claw
Instrument panel
drive's side garnish
Meter bezel
Instrument panel
assembly
Clip
Meter bezel
Clip
Instrument panel
assembly
Center panel
Claw
Clumn cover
Clip
Instrument panel
assembly
Instrument lower
panel
Instrument panel
assembly
Clip
Instrument panel
clock garnish
Claw
Claw
Radio plug
Center panel
Junction brock cover
Clip
Clip
Centr lower panel
Instrument panel
assembly
AB
INSTRUMENT PANEL ASSEMBLY
INTERIOR
52A-6
REMOVAL SERVICE POINT
<<A>> INSTRUMENT PANEL AIR OUTLET
REMOVAL
The instrument panel air outlet may remain on the
instrument panel side when disassembling the lower
panel of the instrument panel and the instrument
panel garnish. Carefully disassemble the parts
remaining on the instrument panel side to prevent
the ball and spring from falling. Assemble the ball
and spring according to the figure to the left if they
fall off.
INSTALLATION SERVICE
>>A<< CENTRE PANEL ASSEMBLY
INSTALLATION
Air mix door cable and blow vent changeover
damper cable connection (Refer to GROUP 55A,
Heater Control Assembly and A/C Switch
).
AC103520AB
Ball
Spring
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст