Mitsubishi Grandis. Manual — part 827
DOOR MIRROR
EXTERIOR
51-43
Step 10. Connector check: F-07-1 and F-07-2 door
mirror (LH) heater element connectors
Q: Is the check result normal?
YES :
Go to Step 11.
NO :
Repair the defective connector.
Step 11. Check of the heater element of the door
mirror (LH)
Check the heater element of the door mirror (LH). (
Refer to
Q: Is the check result normal?
YES :
Go to Step 12.
NO :
Replace the mirror glass of the door mirror
assembly (LH).
Step 12. Connector check: F-07 door mirror
assembly (LH) connector.
Q: Is the check result normal?
YES :
Go to Step 13.
NO :
Repair the defective connector.
Step 13. Resistance measurement at the F-07
door mirror assembly (LH) connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Resistance between F-07 door mirror assembly
connector terminal No.5 and body earth.
OK: 2
Ω or less
Q: Is the check result normal?
YES :
Go to Step 15.
NO :
Go to Step 14.
AC302832
E-07-1
E-07-2
E-07-1
E-07-2
AB
AC303024AB
Connector: F-07
Harness side
AC303024AB
Connector: F-07
Harness side
DOOR MIRROR
EXTERIOR
51-44
Step 14. Check the wiring harness between F-07
door mirror assembly (LH) connector terminal
No.5 and body earth.
NOTE:
Prior to the wiring harness inspection, check
intermediate connector C-27, and repair if necessary.
• Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction
).
NO :
Repair the wiring harness.
Step 15. Voltage measurement at the F-07 door
mirror assembly (LH) connector.
(1) Turn the ignition switch to the ON position.
(2) Rear window defogger switch: ON
(3) Disconnect the connector, and measure at the
wiring harness side.
(4) Voltage between F-07 door mirror assembly
connector terminal No.1 and body earth
OK: System voltage
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction
).
NO :
Go to Step 16.
AC303024AB
Connector: F-07
Harness side
AC302954AC
Connector: C-27
AC303024AB
Connector: F-07
Harness side
AC303097AC
Connector F-07
(harness side)
DOOR MIRROR
EXTERIOR
51-45
Step 16. Check the wiring harness between F-07
door mirror assembly (LH) connector terminal
No.1 and C-205 junction block connector
terminal No.3.
NOTE:
Prior to the wiring harness inspection, check
intermediate connector C-27, and repair if necessary.
• Check the power supply line for open circuit.
Q: Is the check result normal?
YES :
Go to Step 17.
NO :
Repair the wiring harness.
Step 17. Check of the troubles
Check that the heater element works normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
use Troubleshooting/inspection Service
Points
− How to Cope with Intermittent
Malfunction
).
NO :
Replace the door mirror assembly (LH).
ON-VEHICLE SERVICE
Check of door mirror timer function
M1511021700049
1. Turn the ignition switch to the "LOCK" (OFF)
position. Then check that the door mirrors can be
folded and unfolded for approximately 30
seconds.
2. If not, carry out the troubleshooting. (Refer to
GROUP 54B, Troubleshooting
AC303024AB
Connector: F-07
Harness side
AC311691
21
7
16 15
17
18
20 19
1
2
3
4
5
6
23 22
24
25
28
26
27
9
8
10
11
14
12
13
Harness side
AB
Connector: F-205
Junction block (Front view)
AC302954AC
Connector: C-27
DOOR MIRROR
EXTERIOR
51-46
DOOR MIRROR
REMOVAL AND INSTALLATION
M1511006400472
AC311568
AC302936
AC311021
2
4
5
5
1
3
6
4
AB
N
A
A
Section A – A
Front door panel
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст