Mitsubishi Grandis. Manual — part 368
FRONT FOG LAMP
CHASSIS ELECTRICAL
54A-91
ON-VEHICLE SERVICE
FRONT FOG LAMP AIMING
M1542013500024
1. Measure the centre of the front fog lamps, as
shown in the illustration.
2. Set the distance between the screen and the
centre of the front fog lamps as shown in the
illustration.
3. Inflate the types to the specified pressures and
there should be no other load in the vehicles other
than driver or substituted weight of approximately
75 kg placed in the driver’s position.
4. With the engine running at 2,000 r/min, aim the
front fog lamp.
5. Check if the beam shining onto the screen is at
the standard value.
Standard value:
(Vertical direction) 100 mm below horizontal
(H)
(Horizontal direction) Parallel to direction of
vehicle travel
CAUTION
When marking the aiming adjustment, be sure to
mask those lamps which are not being adjusted.
NOTE: The horizontal direction is non-adjustable. If
the deviation of the light beam axis exceeds the
standard value, check to be sure that the mounting
location or some other point is not defective.
BULB REPLACEMENT
M1542001300830
1. Remove the under cover and the splash shield
assembling clips as shown.
AC312857AB
Lamp centre
Fog lamp centre line
Vehicle centre line
Screen
5 m
AC312871AB
Vertical direction
V
H
Lamp centre
Cut off line
High intensity zone
AC312873AB
Vertical direction
Vertical direction
AC303130
FRONT FOG LAMP
CHASSIS ELECTRICAL
54A-92
CAUTION
Don't touch the bulb surface with bare hands or
dirty gloves. If the bulb surface (glass part) gets
dirty, clean it with alcohol or thinner immediately
and dry well, and then install it.
2. Disconnect the connector and withdraw the bulb.
3. Replace the valve, and connect securely the
connector.
FRONT FOG LAMP
REMOVAL AND INSTALLATION
M1542013600043
REMOVAL SERVICE POINTS
<<A>> FOG LAMP ASSEMBLY REMOVAL
Remove the splash shield assembling bolts and clips
as shown.
AC303091AC
Fog lamp bulb
AC312874AB
1
2
2.5 ± 0.3 N·m
Fog lamp switch removal steps
•
Lower panel (Refer to GROUP 52A,
Instrument Panel Assembly
1.
Fog lamp switch
Fog lamp removal steps
<<A>>
2.
Fog lamp assembly
AC303130
REAR FOG LAMP
CHASSIS ELECTRICAL
54A-93
INSPECTION
M1542011201310
FRONT FOG LAMP RELAY CONTINUITY
CHECK
FOG LAMP SWITCH CONTINUITY CHECK
REAR FOG LAMP
REMOVAL AND INSTALLATION
M1542017100051
• Rear fog lamp (integrated with rear combination
lamp) (Refer to
• Fog lamp switch (Refer to
).
AC312876
3
1
4
2
AB
Front fog lamp relay
Front of the vehicle
Battery voltage Tester
connection
Specified
condition
Not supplied
1
− 4
Less than 2
ohms
Supplied
Open circuit
Switch position
Terminal
number
Normal
conditions
OFF
1
− 2
Open circuit
ON
1
− 2
Less than 2
ohms
AC302751AB
SIDE TURN-SIGNAL LAMP
CHASSIS ELECTRICAL
54A-94
INSPECTION
M1542011201332
REAR FOG LAMP RELAY CONTINUITY
CHECK
FOG LAMP SWITCH CONTINUITY CHECK
SIDE TURN-SIGNAL LAMP
SPECIAL TOOL
M1542000600775
AC312922
3
1
4
2
AB
Rear fog lamp relay
Rear fog lamp relay
<L.H. drive vehicles>
<R.H. drive vehicles>
Battery voltage Tester
connection
Specified
condition
Not supplied
1
− 4
Less than 2
ohms
Supplied
Open circuit
Switch position
Terminal
number
Normal
conditions
OFF
5
− 6
Open circuit
ON
5
− 6
Less than 2
ohms
AC302751AB
Tool
Number
Name
Application
MB990784
Ornament
remover
Removal of door mirror outer cover
MB990784
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст