Mitsubishi Grandis. Manual — part 679
DOOR
BODY
42-44
DOUBLE-SIDED TAPE POSITION
REMOVAL SERVICE POINT
<<A>> DOOR OPENING WEATHERSTRIP
LOWER AND DOOR OPENING
WEATHERSTRIP OUTER REMOVAL
Make a fabricated tool as shown in the illustration to
remove the door weatherstrip.
AC311387
AC311028
AC311029
AC311030
AC311031
AC311032
a
b
Section A – A
Section B – B
Door opening weatherstrip outer
Door opening
weatherstrip outer
A
A
B
B
AB
Door opening
weatherstrip outer
Clip
25 mm
Adhesive tape: Double-sided tape a: 5 mm width, 45 mm length and 0.5 mm thickness,
b: 5 mm width, 55 mm length and 0.8 mm thickness
<Rear door>
ACX00555
15 mm
8 mm
AB
4 mm
Thickness:
1 mm
Fabricated
tool
TAILGATE
BODY
42-45
INSTALLATION SERVICE POINTS
>>A<< WATERPROOF FILM
INSTALLATION
CAUTION
When sticking the water-proof film, ensure that
the sealant is applied under the inner panel water
drain hole.
Apply the specified adhesive to the water-proof film
as shown and stick the film.
Specified sealant: 3M ATD Part No.8633 or
equivalent
>>B<< DOOR OUTER OPENING
WEATHERSTRIP OUTER INSTALLATION
The clip colour identifies the left and right
weatherstrips so be sure to see the colours so as to
install correctly.
TAILGATE
SEALANT
M1424000500106
AC310971
AC302817
AC302818
<Rear door>
AB
<Front door>
Waterproof film
Waterproof film
Inner panel water drain hole
Inner panel water drain hole
Applicable side
Identification colour
Left door
Natural (White)
Right door
Blue
Item
Specified sealant
Tailgate hinge
3M ATD Part No.8531 Heavy drip check sealer, 3M
ATD Part No.8646 Automotive joint and seam sealer
or equivalent
TAILGATE
BODY
42-46
SPECIAL TOOLS
M1424000600192
TROUBLESHOOTING
M1424000700230
The tailgate system is controlled by the Smart Wiring
System (SWS). For troubleshooting, refer to GROUP
54B, Troubleshooting
or GROUP 54C,
Troubleshooting
.
ON-VEHICLE SERVICE
TAILGATE FIT ADJUSTMENT
M1424000900182
•
If the striker is not engaged with the tailgate latch
properly, remove the rear end trim (Refer to
GROUP 52A, Interior Trim
the striker mounting screw with an temporary
bolt, and use the special tool (brass bar,
MB990939) and a hammer to tap the bolt head to
adjust the striker.
•
If the clearance between the tailgate and the vehicle
body is uneven, remove the headlining (Refer to
GROUP 52A, Headlining
) and loosen
the body-side tailgate hinge mounting nuts to
adjust the tailgate.
Tool
Number
Name
Use
MB990925
A: MB990939
Bearing and oil seal
installer set
A: Brass bar
Tailgate striker adjustment
MB991223
A: MB991219
B: MB991220
C: MB991221
D: MB991222
Harness set
A: Test harness
B: LED harness
C: LED harness
adapter
D: Probe
Terminal voltage measurement
A: For checking connector pin
contact pressure
B: For checking power supply
circuit
C: For checking power supply
circuit
D: For connecting a locally
sourced tester
MB990925AF
A
MB991223
A
D
C
B
AD
AC105284AB
MB990939
Temporary
bolt
Striker
AC206033AC
Tailgate hinge
TAILGATE
BODY
42-47
ADJUSTMENT OF TAILGATE HEIGHT
M1424003500116
Rotate the damper by using arrow mark on the
damper as a guide to adjust the tailgate height. The
damper height is altered by roughly 3 mm when the
damper is rotated once.
NOTE: If a rattling noise is heard due to the vibration
of the tailgate when the vehicle is being driven,
adjust the damper height until the damper is seated
on the vehicle body. The damper should be seated
on the vehicle body regardless of a rattling noise.
TAILGATE OPENER CHECK
M1424004100025
If the tailgate cannot be opened by operating the
tailgate lock release handle when the tailgate is
unlocked with the vehicle stationary, refer to GROUP
54B, Troubleshooting
or GROUP 54C,
Troubleshooting
AC302561
AC302563
AC302562
AB
A
19 mm
A
Section A – A
Damper
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст