Mitsubishi Grandis. Manual — part 347
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-7
IGNITION SWITCH
SPECIAL TOOLS
M1543000602031
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-8
Tool
Number
Name
Application
MB990784
Ornament remover
Steering column cover
removal
MB991955
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991825
F: MB991826
MUT-III
sub-assembly
A: (V. C.I.) Vehicle
communication
interface
B: MUT-III USB
cable
C: MUT-III Main
harness A
(Vehicles with
CAN
communication
system)
D: MUT-III Main
harness B
(Vehicles without
CAN
communication
system)
E: MUT-III
Measurement
adapter
F: MUT-III Trigger
harness
Diagnosis code check
CAUTION
For vehicles with CAN
communication, use MUT-III
main harness A to send
simulated vehicle speed. If
you connect MUT-III main
harness B instead, the CAN
communication does not
function correctly.
MB990784
MB991910
MB991826
MB991955
MB991911
MB991824
MB991827
MB991825
A
B
C
D
E
F
DO NOT USED
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-9
TROUBLESHOOTING
IGNITION SWITCH
M1543000701198
The ignition switch is controlled by the Smart Wiring
System (SWS). For troubleshooting, refer to
respective Groups below.
• Not using SWS monitor: GROUP 54B,
Troubleshooting
• Using SWS monitor: GROUP 54C,
Troubleshooting
.
IMMOBILIZER
STANDARD FLOW OF DIAGNOSIS
TROUBLESHOOTING
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
DIAGNOSTIC FUNCTION
M1543007000647
HOW TO READ DIAGNOSIS CODE
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
HOW TO ERASE DIAGNOSIS CODE
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
ENCRYPTED CODE REGISTRATION CRITERIA TABLE
M1543026000033
The ignition key contains a transponder (small
transmitter), which retains an unique encrypted code.
Under any of the conditions below, the encrypted
code should be registered in the immobilizer-ECU
again. The immobilizer-ECU can retain maximum
eight different encrypted codes. This means that
maximum eight ignition keys can be registered.
MB991223
A: MB991219
B: MB991220
C: MB991221
D: MB991222
Harness set
A: Test harness
B: LED harness
C: LED harness
adapter
D: Probe
Making voltage and
resistance measurements
during troubleshooting
A: Connect pin contact
pressure inspection
B: Power circuit inspection
C: Power circuit inspection
D: Commercial tester
connection
Tool
Number
Name
Application
MB991223
A
B
C
D
AC
Component to be replaced
Engine-ECU <M/T>
or Engine-A/T-ECU
<A/T>
Immobilizer-ECU
Ignition key
When engine-ECU <M/T> or
engine-A/T-ECU <A/T> is
replaced
−
Should not be
replaced
Should not be replaced
Should be registered
again
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-10
NOTE:
*
: When the engine-ECU <M/T> or
engine-A/T-ECU <A/T> other than immobilizer
system is rewritten, it is not necessary to register the
ignition key again.
CHART CLASSIFIED BY DIAGNOSIS
CODES
M1543007100581
CAUTION
During diagnosis, a diagnosis code associated
with other system may be set when the ignition
switch is turned on with connector(s)
disconnected. On completion, confirm all
systems for diagnosis code(s). If diagnosis
code(s) are set, erase them all.
When Engine-ECU <M/T> or
Engine-A/T-ECU <A/T> is
overwritten
*
−
Should not be
replaced
Should not be replaced
Should be registered
again
When immobilizer-ECU is
replace
Should not be
replaced
−
Should not be replaced
All ignition keys should be
registered again
When ignition key is added
Should not be
replaced
Should not be
replaced
• Additional ignition key
should be registered
• All ignition keys should
be registered again
When ignition key is lost
Should not be
replaced
Should not be
replaced
All the ignition keys other
than the lost one should
be registered again
Component to be replaced
Engine-ECU <M/T>
or Engine-A/T-ECU
<A/T>
Immobilizer-ECU
Ignition key
Code No.
Diagnosis contents
Reference page
11
Transponder communication system or radio interference
of encrypted code.
12
Encrypted codes are not the same or are not registered.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст