Mitsubishi Grandis. Manual — part 177
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-170
Prior to the wiring harness inspection, check
intermediate connectors C-16, C-14 <RH drive
vehicles>, C-27 <LH drive vehicles>, D-16, and
repair if necessary.
• Check the communication lines for open circuit.
Q: Is the check result normal?
YES :
Go to Step 21.
NO :
Repair the wiring harness.
Step 19. Connector check: F-02 power window
sub switch (rear: LH) connector.
Q: Is the check result normal?
YES :
Go to Step 20.
NO :
Repair the connector.
AC310632BA
Connectors: C-14, C-16
C-16
C-14
C-14
C-16
<RHD>
AC310615
AE
Connector: C-16 <LHD>
AC310613
Connector: C-27 <LHD>
AJ
AC310207
AB
Connector: D-16
AC310205
AC
D-03 (B)
9
3
2
1
5 6 7 8
4
10
Connector: D-03 <RHD>
AC310209
Connector: F-02
F-02(B)
AB
Harness side
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-171
Step 20. Check the wiring harness from F-02
power window sub switch (rear: LH) connector
terminal No.6 to the inserted probe.
NOTE:
AC310209
Connector: F-02
F-02(B)
AB
Harness side
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-172
Prior to the wiring harness inspection, check
intermediate connectors C-16, C-14 <RH drive
vehicles>, C-27 <LH drive vehicles>, D-16, and
repair if necessary.
• Check the communication lines for open circuit.
Q: Is the check result normal?
YES :
Go to Step 21.
NO :
Repair the wiring harness.
Step 21. Check the power window sub switch.
Check that the rear left power window works by
means of the power window sub switch (rear: LH)
when the power window lock switch is turned off.
Q: Is the check result normal?
YES :
Go to Step 22.
NO :
Refer to inspection procedure D-3 "Relevant
power window(s) do not work by means of
the front and rear passenger's power
window sub switches
Step 22. Retest the system.
After the power window sub switch (rear: LH) is
replaced, check that the rear left door power window
can be operated by the power window sub switch.
(1) Replace the power window sub switch (rear: LH).
(2) Check that the rear left power window works by
means of the power window main switch.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Replace the power window main switch.
AC310632BA
Connectors: C-14, C-16
C-16
C-14
C-14
C-16
<RHD>
AC310615
AE
Connector: C-16 <LHD>
AC310613
Connector: C-27 <LHD>
AJ
AC310207
AB
Connector: D-16
AC310205
AC
D-03 (B)
9
3
2
1
5 6 7 8
4
10
Connector: D-03 <RHD>
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-173
Inspection Procedure D-5: The window glass lowers automatically while it is rising.
COMMENTS ON TROUBLE SYMPTOM
If the sliding resistance is too great when the window
is being raised or the window glass encounters an
object, the window glass will lower by approximately
150 mm.
POSSIBLE CAUSES
• Improper adjusted door window glass
• Incorrectly installed or warped glass slider
• Malfunction of the power window motor
• Malfunction of the window regulator
DIAGNOSIS PROCEDURE
Step 1. Check the power window anti-trap
function.
Check that the power window anti-trap function
works. Refer to GROUP 42
− Door − On-vehicle
Service
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Refer to Inspection Procedure D-6 "Power
window anti-trap function does not work
normally
."
Step 2. Check the power window operating
current.
Check that the power window operating current is
normal (Refer to GROUP 42
− Door − On-vehicle
Q: Is the check result normal?
YES :
Adjust the door window glass (Refer to
GROUP 42
− Door − On-vehicle service
), and then go to Step 3.
NO :
Replace the defective power window motor
assembly which operating current are
abnormal.
Step 3. Check that the door window glasses are
installed correctly.
Check that the door window glasses are installed
correctly. Refer to GROUP 42
− Door − On-vehicle
Service
.
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Adjust the door window glass (Refer to
GROUP 42
− Door − On-vehicle service
).
Step 4. Retest the system.
Check that the power window does not lower
automatically while it is being raised.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Replace the power window motor assembly
of the defective window.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст