Mitsubishi Grandis. Manual — part 829
DOOR MIRROR
EXTERIOR
51-51
DISASSEMBLY SERVICE POINT
<<A>> CONNECTOR REMOVAL
Use a flat-tipped screwdriver to pull up the retainer
shown slightly (by a few millimeter). Then disengage
the wiring harness terminals to disconnect the
connector.
REASSEMBLY SERVICE POINT
>>A<< ACTUATOR INSTALLATION
1. Check that the wiring harness wires are secured
with the connector as shown.
NOTE: Check that the wires are secured as these
wires may be released from the connector easily.
2. Confirm the wiring harness assembly connectors
of the same colour as the colour engraved on the
actuator. Connect the connectors to the actuator
as shown according to the colours, respectively.
3. Install the actuator to the support assembly.
>>B<< CONNECTOR INSTALLATION
Pull out the connector retainer slightly until it is
loosely fitted. Insert the wiring harness wires of the
shown colours to the connector, respectively. Then
push in the retainer until it clicks in to position.
INSPECTION
M1511019100545
DOOR MIRROR ASSEMBLY OPERATION
CHECK
Remove the door trim, and then connect the battery
to the door mirror assembly connector to check that
the door mirror operates.
AC303079AB
Harness
connector
Retainer
Minus screwdriver
AC303055
AC303571AB
<Door mirror RH>
Connector(gray)
Harness(blue)
Harness(blue)
Harness(yellow)
Harness(yellow)
Harness(white)
Harness(white)
Harness(blue)
Harness(blue)
Connector(gray)
Connector(black)
Connector(black)
<Door mirror LH>
AC302830AB
Engraving(gray)
Engraving(black)
AC303078 AB
Harness
connector
Connector
Retainer
White
Yellow
Black
Purple Gray
Black
Blue
Green
Orange
AC302272
6 7
1 2
9
8
10
4
3
5
AB
Return
Retract
Forward-folding
DOOR MIRROR
EXTERIOR
51-52
ACTUATOR OPERATION CHECK
Battery connection
Direction
operation
• Connect terminal 8 to the negative
battery terminal.
• Connect terminal 10 to the positive
battery terminal.
Up
• Connect terminal 8 to the positive
battery terminal.
• Connect terminal 10 to the negative
battery terminal.
Down
• Connect terminal 8 to the negative
battery terminal.
• Connect terminal 9 to the positive
battery terminal.
Right
• Connect terminal 8 to the positive
battery terminal.
• Connect terminal 9 to the negative
battery terminal.
Left
• Connect terminal 6 to the positive
battery terminal.
• Connect terminal 7 to the negative
battery terminal.
Retract
• Connect terminal 6 to the negative
battery terminal.
• Connect terminal 7 to the positive
battery terminal.
Return
Battery connection
Pivot plate
operation
• Connect terminal 3 to the negative
battery terminal.
• Connect terminal 4 to the positive
battery terminal.
Up
• Connect terminal 3 to the positive
battery terminal.
• Connect terminal 4 to the negative
battery terminal.
Down
• Connect terminal 1 to the positive
battery terminal.
• Connect terminal 2 to the negative
battery terminal.
Right
• Connect terminal 1 to the negative
battery terminal.
• Connect terminal 2 to the positive
battery terminal.
Left
AC309039
1
2
3
4
AB
Pivot plate
DOOR MIRROR
EXTERIOR
51-53
RETRACTOR MOTOR OPERATION
CHECK
Remove the door mirror outer cover. Connect the
battery to the connector shown to check that the
mirror can be folded and unfolded correctly.
⋅
HEATED DOOR MIRROR CHECK
CAUTION
When relocating the car between locations with
extremely different temperatures (warm and
cold), leave the car in the location for a while to
adapt to the temperature prior to checking it.
AC303071
AC303070
AC303073
AC303072
AC309040AB
Pivot plate
Upper in operation
LH (LH in operation)
RH (RH in operation)
LH (RH in operation)
RH (LH in operation)
Lower in operation
Pivot plate
Pivot plate
Pivot plate
AC303551
AC303054
Forward-folding
Return
Retract
AC
Battery connection
Pivot plate
operation
• Connect terminal 1 to the negative
battery terminal.
• Connect terminal 2 to the positive
battery terminal.
Retract
• Connect terminal 1 to the positive
battery terminal.
• Connect terminal 2 to the negative
battery terminal.
Return
AC302283
DOOR MIRROR
EXTERIOR
51-54
Remove the mirror. Check that the resistance value
between the connector terminals (at the back of the
mirror) is at the standard value.
Standard value: 7.5
± 1.1 Ω at 25°C
DOOR MIRROR CONTROL SWITCH
CONTINUITY CHECK
AC209704
AB
Switch position
Tester
connection
Specified
condition
OFF
1
− 2, 1 − 3, 1 − 4,
1
− 6, 1 − 10, 1 −
11, 2
− 9, 3 − 9, 6
− 9, 9 − 10, 9 − 11
Open circuit
Left side OFF
1
− 6, 1 − 10, 1 −
11, 6
− 9, 9 − 10,
9
− 11
Open circuit
Up
1
− 6, 9 − 11
Less than 2
ohms
Down
1
− 11, 6 − 9
Right
1
− 6, 9 − 10
Left
1
− 10, 6 − 9
Right
side
OFF
1
− 2, 1 − 3, 1 − 6,
2
− 9, 3 − 9, 6 − 9
Open circuit
Up
1
− 6, 3 − 9
Less than 2
ohms
Down
1
− 3, 6 − 9
Right
1
− 6, 2 − 9
Left
1
− 2, 6 − 9
Retract and return 1
− 4
Less than 2
ohms
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст