Mitsubishi Grandis. Manual — part 672
WINDOW GLASS
BODY
42-16
CAUTION
•
Be careful not to remove more adhesive than is
necessary.
• Be careful also not to damage the paintwork
on the body surface with the knife. If the
paintwork is damaged, repair the damaged
area with repair paint or anti-rust agent.
6. Use a knife to cut away the remaining adhesive so
that the thickness is within 2 mm around the entire
circumference of the body flange.
7. Finish the flange surfaces so that they are
smooth.
8. If the delta window glass is reused, scrape away
all traces of old adhesive from the glass.
INSTALLATION SERVICE POINT
>>A<<GASKET/CLIP/DELTA WINDOW
GLASS ASSEMBLY INSTALLATION
1. If the delta window glass is reused, follow the
procedure below.
CAUTION
Do not forget gasket.
(1) Fit clips into body.
(2) Cut away clip fitting convex on quarter window
glass.
NOTE: Convex gets broken when quarter
window glass is removed.
CAUTION
Leave the degreased parts for 3 or more minutes
to dry well, before starting on the next step. Do
not touch the degreased parts.
2. Use isopropyl alcohol to degrease the inside and
outside of the delta window glass and the body
flanges.
3. Apply the primer and adhesive.
4. Install the delta window glass by the same
procedure as for the windshield (refer to
ACX00476 AB
AC103606 AC
Cut off these convex parts
WINDOW GLASS
BODY
42-17
QUARTER WINDOW GLASS
REMOVAL AND INSTALLATION
M1422002500333
Pre-removal and Post-installation Operation
• Quarter Trim Upper Removal and Installation (Refer to
• Rear Combination Lamp Assembly Removal and
Installation (Refer to GROUP 54A, Rear Combination
).
AC303564AC
N
1
2
3
1
1
A
A
D
D
B
B
Section A – A
Section B – B
Section C – C
Units: mm
N
12
C
C
Section D – D
10.5
10 15
12
7
15
19.8
7
17
15
15.5
12
15
7
1
Ceramic line
Seal line centre
Seal line centre
Seal line centre
Seal line centre
Primer
Primer
Primer
Adhesive: 3M ATD Part No. 8609 Super Fast Urethane Auto Glass Sealant or equivalent and
3M ATD Part No. 8608 Super Fast Urethane Primer or equivalent
WINDOW GLASS
BODY
42-18
REMOVAL SERVICE POINT
<<A>> QUARTER WINDOW GLASS
REMOVAL
1. In order to protect the body (paint surface), apply
cloth tape to all body areas around the installed
quarter window glass.
2. Apply cloth tape to protect the quarter window
glass.
3. Use glass adhesive knife to cut away adhesive.
CAUTION
Inserting the adhesive knife too deeply into
windshield adhesive may damage quarter
window glass.
4. Keep the glass adhesive knife at right angles with
body flange (from inside the vehicle), and put the
blade at body flange. Then cut away adhesive
along the body flange.
5. Separate the clips by using a piano wire.
6. Make mating marks on the quarter window glass
and body.
7. Use special tool window glass holder( MB990480)
to remove the quarter window glass.
Removal steps
<<A>> >>A<<
1. Quarter window glass
>>A<<
2. Clip
>>A<<
3. Gasket
AC303582AC
Cloth tape
AC002060
AC206381AD
Glass adhesive knife
AC303583AC
Piano wire
Piano wire
Clip
Clip
AC303584AC
MB990480
WINDOW GLASS
BODY
42-19
CAUTION
• Be careful not to remove more adhesive than
is necessary.
• Be careful also not to damage the paintwork
on the body surface with the knife. If the
paintwork is damaged, repair the damaged
area with repair paint or anti-rust agent.
8. Use a knife to cut away the remaining adhesive so
that the thickness is within 2 mm around the entire
circumference of the body flange.
9. Finish the flange surfaces so that they are
smooth.
10.When reusing the quarter window glass, remove
the adhesive still adhering to the quarter window
glass, and clean with isopropyl alcohol.
11.Clean the body side in the same way.
INSTALLATION SERVICE POINT
>>A<< GASKET/CLIP/QUARTER
WINDOW GLASS INSTALLATION
1. Carry out the following procedure to re-install
quarter window glass.
CAUTION
Do not forget gasket.
(1) Fit clips into body.
(2) Cut away clip fitting convex on quarter window
glass.
NOTE: Convex gets broken when quarter
window glass is removed.
CAUTION
Leave the degreased parts for 3 or more minutes
to dry well, before starting on the next step. Do
not touch the degreased parts.
2. Use isopropyl alcohol to degrease the inside and
outside of the quarter window glass and the body
flanges.
3. Apply the primer and adhesive.
4. Install the glass by the same procedure as for the
windshield (Refer to
).
ACX00476 AB
AC103606 AC
Cut off these convex parts
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст