Mitsubishi Grandis. Manual — part 817
FRONT BUMPER ASSEMBLY
EXTERIOR
51-3
FRONT BUMPER ASSEMBLY
ADHESIVE
M1511000500534
FRONT BUMPER ASSEMBLY
REMOVAL AND INSTALLATION
M1511001400648
Application
Specified adhesive
Front three-diamond mark
Double-sided tape [20 mm width 1.2 mm thickness]
AC302774
3
3
AB
Section A – A
Section B – B
Claw
Front bumper
side bracket
Claw
Front bumper
support bracket
AC311852AB
2
4
3
1
A
A
B
B
Splash shield
Removal steps
1. Licence plate bracket
2. Splash shield mounting clips
•
Fog lamp connector connection
•
Headlamp washer hose connection
3. Front bumper assembly
4. Front bumper side bracket
Removal steps (Continued)
FRONT BUMPER ASSEMBLY
EXTERIOR
51-4
DISASSEMBLY AND REASSEMBLY
M1511001600631
AC311138
Double-sided tape:
Generic products [ 20 mm width and 1.2 mm thickness ]
Double-sided tape affixed location
AB
1
AC310587AB
3
2
6
5
5
3
2
4
10
7
6
5
5
N
N
N
N
N
1
11
9
8
Clip
Removal steps
1. Front three-diamond mark
2. Front bumper upper grille
3. Front grille upper reinforcement
4. Bumper centre net
<<A>> >>A<<
5. Rivets
6. Front bumper side plate
7. Towing cover
8. Headlamp washer pop-up unit
assembly
9. Fog lamp assembly
10. Front air dam
11. Front bumper face
Removal steps (Continued)
FRONT BUMPER ASSEMBLY
EXTERIOR
51-5
DISASSEMBLY SERVICE POINT
<<A>> FRONT BUMPER SIDE PLATE
ASSEMBLY REMOVAL
Use a drill (4.0 mm) to make a hole in the rivet to
break it, and then remove the rivet.
REASSEMBLY SERVICE POINT
>>A<< FRONT BUMPER SIDE PLATE
ASSEMBLY
Use recommended tool shown in the illustration to
connect the rivet by the following procedure.
1. Insert the rivet into the base material (front
bumper face and front bumper side plate
assembly).
2. Place the recommended tool over section A of the
rivet.
3. While pushing the flange surface of the rivet with
the recommended tool, press the handle of the
tool.
4. The thin part of section A of the rivet will break
and the rivet will then be attached.
AC303663AB
Rivet
Drill
Bumper face
AC205918
AB
1
2
3
4
Section A
Flange
Rivet
Rivet
Front bumper
side plate
Recommended
tool
Recommended
tool
Front bumper
face
Front bumper face
REAR BUMPER ASSEMBLY
EXTERIOR
51-6
REAR BUMPER ASSEMBLY
REMOVAL AND INSTALLATION
M1511001900568
AC313567
5
6
2
2
AB
Section A – A
Section B – B
Claw
Claw
AC311155AB
A
A
B
B
B
B
B
B
B
A
A
A
A
A
A
A
A
A
A
B
2
6
4
3
3
5
1
Removal steps
•
Tailgate damper lower (Refer to
GROUP 42, Tailgate
1. Rear splash shield
2. Rear bumper assembly
3. Rear bumper centre bracket
4. Rear bumper side bracket
5. Rear bumper side reinforcement
6. Rear under cover side panel(LH)
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст