Mitsubishi Montero Sport (2004+). Manual — part 732
DOOR MIRROR
TSB Revision
EXTERIOR
51-27
2. Pull the mirror downward to remove it from the claws.
INSPECTION
M1511006500190
ELECTRIC REMOTE CONTROL MIRROR
OPERATION CHECK
Follow the table below to check the electric remote control mir-
ror operation.
.
<VEHICLES WITHOUT HEATED MIRROR>
Check that the mirror moves as described in the table when
each terminal is connected to the battery.
.
<VEHICES WITH HEATED MIRROR>
Check that the mirror moves as described in the table when
each terminal is connected to the battery.
AC003989
CLAWS
AB
BATTERY CONNECTION
MIRROR GLASS:
• Connect terminal 3 to the positive
battery terminal
• Connect terminal 1 to the negative
battery terminal
Tilts up.
• Connect terminal 1 to the positive
battery terminal
• Connect terminal 3 to the negative
battery terminal
Tilts down.
• Connect terminal 2 to the positive
battery terminal
• Connect terminal 1 to the negative
battery terminal
Turns to the right.
• Connect terminal 1 to the positive
battery terminal
• Connect terminal 2 to the negative
battery terminal
Turns to the left.
AC003990
AC003991
DOOR MIRROR
TSB Revision
EXTERIOR
51-28
HEATED MIRROR OPERATION CHECK
Ensure that there is continuity between terminal 1 and terminal
4 of the door mirror connector.
DOOR MIRROR CONTROL SWITCH CONTINUITY
CHECK
Follow the table below to check the door mirror control switch
for continuity.
BATTERY CONNECTION
MIRROR GLASS:
• Connect terminal 7 to the positive
battery terminal
• Connect terminal 5 to the negative
battery terminal
Tilts up.
• Connect terminal 5 to the positive
battery terminal
• Connect terminal 7 to the negative
battery terminal
Tilts down.
• Connect terminal 6 to the positive
battery terminal
• Connect terminal 5 to the negative
battery terminal
Turns to the right.
• Connect terminal 5 to the positive
battery terminal
• Connect terminal 6 to the negative
battery terminal
Turns to the left.
AC003991
SWITCH POSITION TESTER
CONNECTION
SPECIFIED
CONDITION
Left side
Up
4
− 8, 6 − 7
Less than 2 ohms
Down
4
− 7, 6 − 8
Less than 2 ohms
Right
3
− 6, 4 − 7
Less than 2 ohms
Left
3
− 4, 6 − 7
Less than 2 ohms
Right side Up
2
− 4, 6 − 7
Less than 2 ohms
Down
2
− 6, 4 − 7
Less than 2 ohms
Right
4
− 7, 6 − 9
Less than 2 ohms
Left
4
− 9, 6 − 7
Less than 2 ohms
5
4
6
3
2
1
9
8
7
AC001682
SPECIFICATIONS
TSB Revision
EXTERIOR
51-29
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1511015300183
SERVICE SPECIFICATIONS
M1511000300187
SEALANTS AND ADHESIVES
M1511000500170
ITEM
SPECIFICATION
Front bumper
Fog light bracket screw
0.7 N
⋅m (6.2 in-lb)
Fog light screw
2.5 N
⋅m (22 in-lb)
Lift gate garnish
Lift gate garnish nut
4.9 N
⋅m (43 in-lb)
Rear wiper and washer
Wiper arm and blade assembly nut
7.5 N
⋅m (65 in-lb)
Wiper motor
4.9 N
⋅m (43 in-lb)
Side step
Side step pipe assembly
11 N
⋅m (98 in-lb)
Under floor spare tire carrier
Spare tire carrier bolt
12 N
⋅m (104 in-lb)
Windshield wiper and washer
Washer tank bolt
4.9 N
⋅m (43 in-lb)
Wiper arm and blade assembly nut
13 N
⋅m (113 in-lb)
Wiper link assembly nut
4.9 N
⋅m (43 in-lb)
Wiper motor bolt
4.9 N
⋅m (43 in-lb)
ITEM
STANDARD VALUE
Windshield wiper blade position
installation mm (in)
Driver's side
26
± 5 (1.0 ± 0.2)
Passenger's side
30
− 40 (1.2 − 1.5)
Rear wiper blade position installation mm (in)
70
± 5 (2.8 ± 0.2)
ITEM
SPECIFICATION
Door molding
Adhesive tape: Double-sided tape, <A, C, E [1.2 mm
(0.05 in) thickness], B [5 mm (0.2 in) width and 1.2 mm
(0.05 in) thickness], D [12 mm (0.5 in) width and 1.2
mm (0.05 in) thickness]>
Side step molding
Adhesive tape: Double-sided tape [23 mm (0.9 in)
wide and 0.8 mm (0.03 in) thickness]
Delta cover inner
Adhesive tape: Double-sided tape [5 mm (0.2 in) width
and 0.4 mm (0.02 in) thickness]
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст