Mitsubishi Montero Sport (2004+). Manual — part 730
REAR WIPER AND WASHER
TSB Revision
EXTERIOR
51-19
WINDSHIELD WASHER FLUID EJECTION CHECK
Adjust the ejection angle by moving a ball in the nozzle.
A: 325 mm (12.8 inches)
B: 385 mm (15.2 inches)
C: 140 mm (5.5 inches)
D: 195 mm (7.7 inches)
E: 430 mm (17.0 inches)
F: 290 mm (11.4 inches)
G: 375 mm (14.8 inches)
H: 195 mm (7.7 inches)
I: 70 mm (2.8 inches)
J: 50 mm (2.0 inches)
REAR WIPER AND WASHER
GENERAL DESCRIPTION
M1511000100268
OPERATION
Low-speed wiper operation
• When the rear wiper switch is placed in the "ON"
position with the ignition switch in the "ACC" or
"ON" position, wiper operate continuously at low
speed.
Auto wiper stop operation
• When the rear wiper switch is placed in the "OFF"
position, the cam contacts of wiper motor causes
current to flow through the auto wiper stop circuit,
allowing the wiper blades to cycle before they
reach to the stop positions.
Intermittent wiper operation
• When the rear wiper switch is placed in the
"INTERMITTENT" position with the ignition
switch in the "ACC" or "ON" position, the rear
intermittent wiper relay contacts to close and
open repeatedly.
• When the contacts are closed, the wiper motor is
energized.
• When the rear wiper motor is energized, the rear
intermittent wiper relay contacts open; however,
the cam contacts keep the rear wiper motor ener-
gized until the wiper blades return to their stop
position.
Washer-wiper operation
• When the rear washer switch is turned "ACC" or
"ON" position, current flows through multi-pur-
pose fuse number 8 remote-controlled mirror
switch, remote-control mirror, remote-controlled
mirror switch, and ground, causing the mirror to
move.
AC003896
CERAMIC END LINE
RH
LH
I
J
E
A
B
C
D
F
H
G
AB
CENTER LINE
REAR WIPER AND WASHER
TSB Revision
EXTERIOR
51-20
REAR WIPER AND WASHER
REMOVAL AND INSTALLATION
M1511008800090
AC003898
7.5 N·m
66 in-lb
4.9 N·m
43 in-lb
3
4
5
2
7
6
6
9
8
1
AB
1. REAR INTERMITTENT WIPER
RELAY
REAR WIPER MOTOR ASSEMBLY
REMOVAL STEPS
>>B<<
2. REAR WIPER ARM AND BLADE
ASSEMBLY
>>A<<
3. GROMMET
• LIFTGATE GARNISH (REFER TO
4. GROMMET
5. REAR WIPER MOTOR ASSEMBLY
REAR WASHER HOSE REMOVAL
STEPS
• QUARTER TRIM, LOWER <RH>
(REFER TO GROUP 52A, TRIMS
6. REAR WASHER HOSE
7. WASHER NOZZLE
REAR WASHER TANK ASSEMBLY
AND REAR WASHER MOTOR
REMOVAL STEPS
• QUARTER TRIM, LOWER <RH>
(REFER TO GROUP 52A, TRIMS
• WASHER FLUID DRAINING
6. REAR WASHER HOSE
REAR WIPER AND WASHER
TSB Revision
EXTERIOR
51-21
NOTE: For removal and installation of the wiper and
washer switch, refer to GROUP 37A, Steering Wheel
and Shaft
INSTALLATION SERVICE POINTS
.
>>A<<GROMMET INSTALLATION
Install the grommet so that the arrow points downwards.
.
>>B<<REAR WIPER ARM AND BLADE ASSEMBLY
INSTALLATION
Install the wiper blade so that the tip stops at the standard posi-
tion (standard value), and also so that the lower section of the
wiper blade enters the middle of the defogger pattern.
Standard value : 70
± 5 mm (2.8 ± 0.2 inches)
INSPECTION
M1511008600212
REAR WIPER AND WASHER SWITCH CHECK
Follow the table below to check the rear wiper and washer
switch for continuity.
8. REAR WASHER TANK
9. REAR WASHER MOTOR
REAR WASHER TANK ASSEMBLY
AND REAR WASHER MOTOR
REMOVAL STEPS (Continued)
AC003911
GROMMET
ARROW
AB
Y0124AA
AC003912
CERAMIC SECTION
DEFOGGER PATTERN
AB
SWITCH POSITION
TERMINAL
CONNECTION
SPECIFIED
CONDITION
Windshield intermittent wiper
switch ON
3
− 10
Less than 2
ohms
Rear wiper switch ON
4
− 10
Less than 2
ohms
Rear washer switch ON
2
− 10
Less than 2
ohms
AC003910
REAR WIPER AND WASHER
TSB Revision
EXTERIOR
51-22
REAR WIPER MOTOR CHECK
Check the wiper motor after first disconnecting the wiring har-
ness connector, and with the wiper motor remaining installed to
the body.
.
WIPER MOTOR OPERATION
Connect a battery to the wiper motor as shown in the illustra-
tion and inspect the motor operation.
.
WIPER MOTOR AT STOP POSITION OPERATION
1. Run the wiper motor, disconnect the battery, and stop the
motor.
2. Reconnect the battery as shown in the illustration, and
confirm that after the motor starts turning it stops at the
automatic stop position.
REAR INTERMITTENT WIPER RELAY CHECK
1. Check that there is continuity between terminals (1) and (2).
2. Connect terminals (4), (5) to the battery (+) terminal.
3. Check that there is battery voltage at terminal (2) for
intermittent periods of eight seconds when terminal (7) is
connected to the battery (-) terminal.
REAR WASHER MOTOR CHECK
1. With the washer motor installed to the washer tank, fill the
washer tank with water.
2. When the battery is connected as shown in the figure, check
that the washer squirts out strongly.
AC003913
OPERATION CHECK
STOP POSITION CHECK
AB
AC003915
REAR INTERMITTENT
WIPER RELAY
AB
AC003916
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст