Mitsubishi Montero Sport (2004+). Manual — part 731
MARK
TSB Revision
EXTERIOR
51-23
REAR WASHER FLUID EJECTION CHECK
Move the nozzle to adjust so that the water is sprayed out
within the range shown in the illustration.
A: 55 mm (2.16 inches)
B: 38 mm (1.49 inches)
C: 20 mm (0.78 inches)
D: 207 mm (8.1 inches)
MARK
REMOVAL AND INSTALLATION
M1511011800584
Y0136AA
AC004168
A
B C
C
A
D
CERAMIC LINE
AB
AC200769
1
2
6
5
4
3
AE
>>A<< 1. "MONTERO SPORT" MARK
>>A<<
2. "MONTERO SPORT" MARK
>>A<<
3. "AWD" DECAL
>>A<<
4. "GRADE" MARK
>>A<<
5. "3-DIAMOND" MARK
>>A<<
6. "MITSUBISHI" MARK
MARK
TSB Revision
EXTERIOR
51-24
INSTALLATION SERVICE POINT
.
>>A<< MARK INSTALLATION
1. Installation position
Attach to the position shown in the illustration.
AC103788
AC103787
AD
"MONTERO SPORT" MARK
ALIGN TO PRESS LINE
FENDER
PANEL
END LINE
LIFTGATE
GARNISH
END LINE
ALIGN TO NOTCH
LIFTGATE GARNISH
END LINE
LIFTGATE GARNISH END LINE
ALIGN TO PRESS LINE
LIFTGATE
END LINE
LIFTGATE GARNISH END LINE
LIFTGATE GARNISH
CENTER LINE
LIFTGATE GARNISH
END LINE
LIFTGATE GARNISH
END LINE
14.8 mm
(0.58 in)
"GRADE" MARK
"AWD" DECAL, "GRADE" MARK
"3-DIAMOND" MARK
DOOR MIRROR
TSB Revision
EXTERIOR
51-25
2. Installation procedure
(1) Use 3M
AAD Part number 8906 or equivalent to clean
the mark installation surfaces on the body.
CAUTION
When attaching the marks, the surrounding temperature
should be 20
− 38°C (60 − 100°F) and the air should be
completely free from dust. If the surrounding temperature
is low than 20
°C (60°F), the marks and their application
surface on the body should be heated to 20
− 38°C (60 −
100
°F).
(2) Peel off the backing paper from the reverse side of the
marks, carefully attach the marks to the vehicle body in
the exact position shown.
DOOR MIRROR
SPECIAL TOOL
M1511000600735
AC003986
NOTCH
ALIGN TO LOWER END
OF LIFTGATE GARNISH
LIFTGATE GARNISH CENTER LINE
AB
MITSUBISHI MARK
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB990784 Ornament
remover
General service tool
Removal of remote
controlled mirror switch
MB990784
DOOR MIRROR
TSB Revision
EXTERIOR
51-26
DOOR MIRROR
REMOVAL AND INSTALLATION
M1511006400397
Required Special Tool:
• MB990784: Ornament Remover
REMOVAL SERVICE POINT
.
<<A>> MIRROR REMOVAL
1. Tilt the mirror upward by hand, insert a flat-tipped
screwdriver onto which protective tape has been wound,
and then pry the claws off of the actuator.
AC003987
3
2
5
4
2
1
ADHESIVE TAPE:
DOUBLE-SIDED TAPE 5 mm (0.2 in)
WIDTH AND 0.4 mm (0.02 in) THICKNESS
AB
1. REMOTE CONTROLLED MIRROR
SWITCH
DOOR MIRROR REMOVAL STEPS
2. DELTA COVER, INNER
3. HARNESS CONNECTOR
<VEHICLES WITH REMOTE
CONTROLLED MIRROR>
4. MIRROR ASSEMBLY
<<A>>
5. MIRROR
DOOR MIRROR REMOVAL STEPS
AC003988
CLAWS
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст