Mitsubishi Montero Sport (2004+). Manual — part 729
ROOF RAIL
TSB Revision
EXTERIOR
51-15
ROOF RAIL
REMOVAL AND INSTALLATION
M1511016600080
WINDSHIELD WIPER AND WASHER
GENERAL DESCRIPTION
M1511000100257
OPERATION
Low-speed (and high-speed) wiper operation
• When the wiper switch is placed in the "LOW"
position with the ignition switch in the "ACC" or
"ON" position, wipers operate continuously at low
speed.
• Placing the wiper switch in the "HIGH" position
causes the wipers to operate at high speed.
Auto wiper stop operation
• When the wiper switch is placed in the "OFF"
position, the cam contacts of wiper motor causes
current to flow through the auto wiper stop circuit,
allowing the wiper blades to cycle before they
reach to the stop positions.
Intermittent wiper operation
• When the wiper switch is placed in the "INTER-
MITTENT" position with the ignition switch in the
"ACC" or "ON" position, the intermittent wiper
relay is energized causing the intermittent wiper
relay contacts to close and open repeatedly.
• When the contacts are closed, the wiper motor is
energized.
• When the wiper motor is energized, the relay
contacts open; however, the cam contacts keep
the wiper motor energized until the wiper blades
return to their stop position.
Washer-wiper operation
• When the washer switch is turned "ON," the
intermittent wiper relay contacts close causing
wipers to cycle one to two times.
Pre-removal and Post-installation Operation
• Headlining Removal and Installation
AC200767
ROOF RAIL ASSEMBLY
AD
N
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-16
WINDSHIELD WIPER AND WASHER
REMOVAL AND INSTALLATION
M1511008200292
NOTE: For removal and installation of the column
switch assembly (wiper and washer switch), refer to
GROUP 37A, Column switch
AC003861
13 N·m
113 in-lb
1
7
8
5
4.9 N·m
43 in-lb
4.9 N·m
43 in-lb
4.9 N·m
43 in-lb
4.9 N·m
43 in-lb
3
4
4.9 N·m
43 in-lb
2
6
5
AD
1
WIPER MOTOR AND LINK ASSEMBLY
REMOVAL STEPS
>>A<<
1. WIPER ARM AND BLADE
ASSEMBLY
2. FRONT DECK GARNISH
<<A>>
3. WIPER MOTOR ASSEMBLY
4. WIPER LINK ASSEMBLY
WIPER MOTOR AND LINK ASSEMBLY
REMOVAL STEPS
5. WASHER HOSE
6. WASHER NOZZLE
WASHER TANK REMOVAL STEPS
• FRONT BUMPER ASSEMBLY
(REFER TO P.51-2
.)
• WASHER FLUID DRAINING AND
SUPPLYING
5. WASHER HOSE
7. WASHER TANK ASSEMBLY
8. WASHER MOTOR
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-17
REMOVAL SERVICE POINT
.
<<A>>WIPER MOTOR ASSEMBLY REMOVAL
CAUTION
Auto-stop angle controlled so do not remove the crank
arm from the wiper motor unless necessary. When remov-
ing, mark the crank arm and wiper motor.
Use a flat-tipped screwdriver to remove the connection
between the wiper motor crank arm and link assembly.
INSTALLATION SERVICE POINT
.
>>A<<WIPER ARM AND BLADE ASSEMBLY INSTALLA-
TION
Install the wiper blade at the specified position (standard
value).
Standard value : Driver's side (A) : 26
± 5 mm (1.0 ± 0.2
inches) Passenger's side (B) : 30
− 40 mm (1.2 − 1.5
inches)
INSPECTION
M1511007700357
WINDSHIELD WIPER AND WINDSHIELD WASHER
SWITCH CHECK
Follow the table below to check the windshield wiper and
washer switch for continuity.
AC003862
WIPER MOTOR
CRANK ARM
LINK ASSEMBLY
AB
AC000427AB
DRIVER'S
SIDE (A)
PASSENGER'S
SIDE (B)
FRONT DECK GARNISH END
SWITCH POSITION
TERMINAL
CONNECTION
SPECIFIED
CONDITION
OFF
7
− 8
Less than 2
ohms
Windshield intermittent wiper
switch ON
7
− 8
Less than 2
ohms
Windshield low-speed wiper
switch ON
8
− 10
Less than 2
ohms
Windshield high-speed wiper
switch ON
9
− 10
Less than 2
ohms
Windshield washer switch ON 6
− 10
Less than 2
ohms
AC003910
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-18
INTERMITTENT WIPER RELAY (INTERMITTENT
OPERATION INSPECTION)
1. Connect the column switch connector.
2. Turn the ignition switch to "ACC."
3. Inspect the intermittent operation time when the wiper switch
is turned to "INTERMITTENT."
Vehicle with variable intermittent control
FAST: Approximately 2 seconds
SLOW: Approximately 15 seconds
FRONT WIPER MOTOR CHECK
Check the wiper motor after disconnecting the wiring harness
connector, and with the wiper motor remaining installed to the
body.
.
WIPER MOTOR AT LOW-SPEED AND HIGH-SPEED
OPERATION
Connect a battery to the wiper motor as shown in the illustra-
tion and inspect motor operation at low-speed and high-speed.
.
WIPER MOTOR AT STOP POSITION OPERATION
1. Run the wiper motor at low-speed, disconnect the battery,
and stop the motor.
2. Reconnect the battery as shown in the illustration, and
confirm that after the motor starts turning at low-speed, and
stops at the automatic stop position.
FRONT WASHER MOTOR CHECK
1. The windshield washer tank assembly should be installed
and the windshield washer tank should be filled with water
when checking the washer motor.
2. Check that water is sprayed out strongly when battery
voltage is applied to terminal (1) and terminal (2) is
grounded.
AC003875
CHECK OPERATION
LOW SPEED HIGH SPEED
LOW SPEED
AUTOMATIC
STOP
STOP POSITION CHECK
AB
AC003881
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст