Mitsubishi Montero Sport (2004+). Manual — part 424
PROPELLER SHAFT
TSB Revision
PROPELLER SHAFT
25-15
>>C<< SNAP RING INSTALLATION
1. Install a snap ring to one side of the journal.
2. Use special tool MB990840 and MB991410 at the opposite
side of the installed snap ring to press in the journal bearing
toward the snap ring.
CAUTION
Always use snap rings of equal thickness on both sides.
3. Install the snap ring on the opposite side, and measure the
clearance of the snap ring groove with a feeler gauge.
Standard value (A): 0.06 mm (0.002 inch) or less
4. If the clearance exceeds the standard value, adjust by
changing the thickness of the snap ring.
AC003888
TYPE 1
TYPE 2
AB
AC003889AB
TYPE 1
TYPE 2
MB990840
MB990840
MB991410
SNAP RING
SNAP RING
THICKNESS
TYPE 1 mm (in)
THICKNESS
TYPE 2 mm (in)
IDENTIFICATION
COLOR
1.28 (0.050)
1.50 (0.059)
−
1.31 (0.052)
1.55 (0.061)
Yellow
1.34 (0.053)
1.60 (0.063)
Blue
1.37 (0.054)
1.65 (0.065)
Purple
AC003890 AB
TYPE 1
TYPE 2
SNAP RING
SNAP RING
SPECIFICATIONS
TSB Revision
PROPELLER SHAFT
25-16
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1251001600139
GENERAL SPECIFICATIONS
M1251000200149
<RWD>
<4WD>
SERVICE SPECIFICATIONS
M1251000300102
LUBRICANT
M1251000400121
ITEM
SPECIFICATION
Center bearing assembly nut
34 N
⋅m (25 ft-lb)
Center yoke nut
186 N
⋅m (137 ft-lb)
Front propeller shaft assembly nut
49
− 59 N⋅m (36 − 43 ft-lb)
Front propeller shaft assembly to sleeve flange
connecting nut
49
− 59 N⋅m (36 − 43 ft-lb)
Propeller shaft assembly nut
98
− 108 N⋅m (72 − 80 ft-lb)
Transfer gear oil drain plug
30
− 34 N⋅m (22 − 25 ft-lb)
Transfer gear oil filler plug
30
− 34 N⋅m (22 − 25 ft-lb)
ITEM
SPECIFICATION
Propeller shaft length (joint to joint) ODmm (in)
Front
613
× 75 (24.1 × 3.0)
Rear
783
× 75 (30.8 × 3.0)
Universal joint journal OD mm (in)
19.06 (0.750)
ITEM
SPECIFICATION
Front propeller shaft length (joint to joint)
× ODmm (in)
470
× 50.8 (18.5 × 2.00)
Rear propeller shaft length (joint to joint)
× ODmm (in)
959
× 75 (37.8 × 3.0)
Universal joint journal OD mm (in)
Front propeller shaft
14.689 (0.5783)
Rear propeller shaft
19.06 (0.750)
ITEM
STANDARD VALUE
LIMIT
Propeller shaft run-out mm (in)
−
0.6 (0.02)
Clearance between snap ring and groove wall of yoke mm (in)
0.06 (0.002) or less
−
ITEM
SPECIFIED LUBRICANT
QUANTITY
Propeller shaft sleeve yoke
Hypoid gear oil API classification GL-4 or higher
SAE viscosity 80W, 75W-80W
As required
SPECIFICATIONS
TSB Revision
PROPELLER SHAFT
25-17
COMPONENT IDENTIFICATION
M1251001700084
SNAP RING
ITEM
IDENTIFICATION COLOR
Type 1 (external snap ring type) thickness mm (in)
1.28 (0.050)
−
1.31 (0.052)
Yellow
1.34 (0.053)
Blue
1.37 (0.054)
Purple
Type 2 (internal snap ring type) thickness mm (in)
1.50 (0.059)
−
1.55 (0.061)
Yellow
1.60 (0.063)
Blue
1.65 (0.065)
Purple
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст