Mitsubishi Eclipse. Manual — part 714

SPECIFICATIONS

TSB Revision

POWER PLANT MOUNT

32-13

SPECIFICATIONS

FASTENER TIGHTENING SPECIFICATIONS

M1321004100182

SERVICE SPECIFICATION

M1321000300173

ITEMS

SPECIFICATIONS

Centermember front mounting bolt

93

± 15 N⋅m (69 ± 11 ft-lb)

Centermember rear mounting bolt

74

± 4 N⋅m (55 ± 3 ft-lb)

Crossmember and stay connecting bolt <2.4L ENGINE>

74

± 4 N⋅m (55 ± 3 ft-lb)

Crossmember mounting bolt

108

± 10 N⋅m (80 ± 7 ft-lb)

Crossmember mounting nut

88

± 10 N⋅m (65 ± 7 ft-lb)

Dynamic damper bolt <3.0L ENGINE>

4.9

± 1.0 N⋅m (44 ± 8 in-lb)

Engine mount bracket bolt

86

± 12 N⋅m (64 ± 8 ft-lb)

Engine mount bracket nut

86

± 12 N⋅m (64 ± 8 ft-lb)

Engine mount insulator mounting bolt

81

± 12 N⋅m (60 ± 9 ft-lb)

Engine mount stay bolt <3.0L ENGINE>

35

± 5 N⋅m (26 ± 4 ft-lb)

Lower arm and crossmember connecting nut

108

± 10 N⋅m (80 ± 7 ft-lb)

Lower arm mount bolt

81

± 12 N⋅m (60 ± 9 ft-lb)

Transaxle and front roll stopper connecting bolt

45

± 5 N⋅m (34 ± 3 ft-lb)

Transaxle and front roll stopper connecting nut

45

± 10 N⋅m (34 ± 7 ft-lb)

Transaxle and rear roll stopper connecting bolt

45

± 5 N⋅m (34 ± 3 ft-lb)

Transaxle and rear roll stopper connecting nut

45

± 5 N⋅m (34 ± 3 ft-lb)

Transaxle mount bracket nut

57

± 7 N⋅m (42 ± 5 ft-lb)

Transaxle mount insulator mounting nut

81

± 12 N⋅m (60 ± 9 ft-lb)

ITEMS

STANDARD VALUE

Inner pipe projection mm (in)

Bushing A

9.0

± 1.0 (0.35 ± 0.04)

Bushing B

2.4L ENGINE

4.0

± 1.0 (0.16 ± 0.04)

3.0L ENGINE

9.0

± 1.0 (0.35 ± 0.04)

Bushing C

4.0

± 0.5 (0.16 ± 0.02)

NOTES

00-1

GROUP 00

GENERAL

CONTENTS

HOW TO USE THIS MANUAL. . . . . .

00-2

TROUBLESHOOTING GUIDELINES

00-6

HOW TO USE
TROUBLESHOOTING/INSPECTION
SERVICE POINTS . . . . . . . . . . . . . . .

00-6

VEHICLE IDENTIFICATION . . . . . . .

00-15

VEHICLE IDENTIFICATION . . . . . . . . . . . .

00-15

VEHICLE IDENTIFICATION CODE PLATE

00-18

PRECAUTIONS BEFORE SERVICE.

00-23

TOWING AND HOISTING . . . . . . . . .

00-26

GENERAL DATA AND
SPECIFICATIONS . . . . . . . . . . . . . . .

00-30

TIGHTENING TORQUE . . . . . . . . . . .

00-36

LUBRICATION AND MAINTENANCE

00-37

RECOMMENDED LUBRICANTS AND
LUBRICANT CAPACITIES TABLE . .

00-38

SCHEDULED MAINTENANCE
TABLE . . . . . . . . . . . . . . . . . . . . . . . .

00-41

MAINTENANCE SERVICE . . . . . . . .

00-44

1. FUEL SYSTEM (TANK, PIPE LINE AND
CONNECTION, AND FUEL TANK FILLER
TUBE CAP) (CHECK FOR LEAKS) . . . . . .

00-44

2. FUEL HOSES (CHECK CONDITION) . .

00-44

3. AIR CLEANER ELEMENT (REPLACE) .

00-44

4. EVAPORATIVE EMISSION CONTROL

SYSTEM (EXCEPT EVAPORATIVE
EMISSIONCANISTER) (CHECK FOR
LEAKS AND CLOGGING) . . . . . . . . . . . . . .

00-44

5. SPARK PLUGS (REPLACE) . . . . . . . . . .

00-45

6. IGNITION CABLES (REPLACE) . . . . . . .

00-45

7. DISTRIBUTOR CAP AND ROTOR (CHECK)
<3.0L ENGINE>. . . . . . . . . . . . . . . . . . . . . .

00-46

8. TIMING BELT (REPLACE) . . . . . . . . . . .

00-46

9. DRIVE BELT (FOR THE GENERATOR,
WATER PUMP, POWER STEERING PUMP
(CHECK CONDITION) . . . . . . . . . . . . . . . .

00-46

10. ENGINE OIL (CHANGE) . . . . . . . . . . . .

00-53

11. ENGINE OIL FILTER (REPLACE) . . . .

00-54

12. MANUAL TRANSAXLE OIL . . . . . . . . .

00-55

13. AUTOMATIC TRANSMISSION FLUID .

00-56

14. ENGINE COOLANT (CHANGE) . . . . . .

00-58

15. DISC BRAKE PADS (INSPECT FOR
WEAR). . . . . . . . . . . . . . . . . . . . . . . . . . . . .

00-60

16. REAR DRUM BRAKE LININGS AND REAR
WHEEL CYLINDERS (INSPECT FOR WEAR
AND LEAKS) . . . . . . . . . . . . . . . . . . . . . . . .

00-60

17. BRAKE HOSES (CHECK FOR
DETERIORATION OR LEAKS) . . . . . . . . . .

00-61

18. BALL JOINT AND STEERING LINKAGE
SEALS (INSPECT FOR GREASE LEAKS
AND DAMAGE) . . . . . . . . . . . . . . . . . . . . . .

00-61

19. DRIVE SHAFT BOOTS (INSPECT FOR
GREASE LEAKS AND DAMAGE). . . . . . . .

00-61

20. SRS AIR BAG (INSPECT FOR SRS
SYSTEM). . . . . . . . . . . . . . . . . . . . . . . . . . .

00-62

21. EXHAUST SYSTEM (CONNECTIONS,
PIPES AND CONVERTER HEAT SHIELDS)
(CHECK AND SERVICE AS REQUIRED). .

00-67

22. TIRES (ROTATE) . . . . . . . . . . . . . . . . .

00-68

MAIN SEALANT AND ADHESIVE
TABLE. . . . . . . . . . . . . . . . . . . . . . . . .

00-68

HOW TO USE THIS MANUAL

TSB Revision

GENERAL

00-2

HOW TO USE THIS MANUAL

M1001000100295

MAINTENANCE, REPAIR AND
SERVICING EXPLANATIONS

This manual provides explanations, etc. concerning
procedures for the inspection, maintenance, repair
and servicing of the subject model. Unless otherwise
specified, each service procedure covers all models.
Procedures covering specific models are identified
by the model codes, or similar designation (engine
type, transaxle type, etc.). A description of these des-
ignations is covered in this manual under "VEHICLE
IDENTIFICATION."

.

ON-VEHICLE SERVICE
"ON-VEHICLE SERVICE" section has procedures
for performing inspections and adjustments of partic-
ularly important components. These procedures are
done with regard to maintenance and servicing, but
other inspections (looseness, play, cracking, dam-
age, etc.) must also be performed.

.

SERVICE PROCEDURES
The service steps are arranged in numerical order.
Attention to be paid in performing vehicle service are
described in detail in SERVICE POINTS.

DEFINITION OF TERMS

.

STANDARD VALUE
Indicates the value used as the standard for judging
whether or not a part or setting up on inspection is
correct.

.

LIMIT
Shows the maximum or minimum value for judging
whether or not a part or setting up on inspection is
acceptable.

.

REFERENCE VALUE
Indicates the adjustment value prior to starting the
work (presented in order to facilitate assembly and
adjustment procedures, and so they can be com-
pleted in a shorter time).

.

DANGER, WARNING, AND CAUTION
DANGER, WARNING, and CAUTION call special
attention to a necessary action or to an action that
must be avoided. The differences among DANGER,
WARNING, and CAUTION are as follows:

• If a DANGER is not followed, the result is severe

bodily harm or even death.

• If a WARNING is not followed, the result could be

bodily injury.

• If a CAUTION is not followed, the result could be

damage to the vehicle, vehicle components or
service equipment.

TIGHTENING TORQUE INDICATION

The tightening torque indicates a median and its tol-
erance by a unit of N

⋅m(in-lb) or N⋅m (ft-lb). For fas-

teners with no assigned torque value, refer to

P.00-36

.

SPECIAL TOOL NOTE

Only MMC special tool part numbers are called out in
the repair sections of this manual. Please refer to the
special tool cross reference chart located at the
beginning of each group for a cross reference from
the MMC special tool number to the special tool
number that is available in your market.

ABBREVIATIONS

The following abbreviations are used in this manual
for classification of model types.
M/T:Indicates manual transaxle, or models equipped

with manual transaxle.

A/T: Indicates automatic transaxle, or models

equipped with automatic transaxle.

MFI: Indicates multiport fuel injection, or engines

equipped with multiport fuel injection.

A/C: Indicates air conditioning.
2.4L Engine: Indicates the 2.4 liter <4G64> engine,

or a model equipped with such an engine.

3.0L Engine: Indicates the 3.0 liter <6G72> engine,

or a model equipped with such an engine.

PCM: Powertrain control module
ECM: Engine control module
SWS: Simplified Wiring System