Mitsubishi Eclipse. Manual — part 712
TRANSAXLE MOUNTING
TSB Revision
POWER PLANT MOUNT
32-5
INSTALLATION SERVICE POINT
.
>>A<< ENGINE MOUNT STOPPER INSTALLATION
Clamp the engine mount stopper so that the arrow points in the
direction as shown in the diagram.
INSPECTION
M1321001200124
• Check the insulators for cracks, separation or deformation.
• Check the front insulator stoppers for deformation.
TRANSAXLE MOUNTING
REMOVAL AND INSTALLATION
M1321001400418
CAUTION
Mounting locations marked by
*
should be provisionally tightened, and then fully tightened after plac-
ing the vehicle horizontally and loading the full weight of the engine on the vehicle body.
AC000300
ENGINE SIDE
DYNAMIC DAMPER
ARROW
ENGINE
MOUNT
STOPPER
ENGINE MOUNT BRACKET
AB
Pre-removal and Post-installation Operation
• Air Cleaner Assembly Removal and Installation (Refer to GROUP 15, Air Cleaner
• Battery and Battery Tray Removal and Installation (Refer to GROUP 54A, Battery
• Centermember Removal and Installation (Refer to
.)
• Transaxle and Rear Roll Stopper Connecting Bolt Removal and Installation (Refer to
.)
• Rear Roll Stopper Bracket Removal and Installation <2.4L Engine-M/T> (Refer to GROUP 22B, Transaxle
<2.4L Engine-A/T> (Refer to GROUP 23B, Transaxle
.)
AC000301 AB
1
2
81 ± 12 N·m*
60 ± 9 ft-lb*
57 ± 7 N·m
42 ± 5 ft-lb
N
REMOVAL STEPS
<<A>>
1.
TRANSAXLE MOUNT BRACKET
>>A<<
2.
TRANSAXLE MOUNT STOPPER
TRANSAXLE MOUNTING
TSB Revision
POWER PLANT MOUNT
32-6
Required Special Tools:
• MB991453: Engine Hanger Assembly
• MZ203827: Engine Lifter
• MB991454: Engine Hanger
• MB991895: Engine Lifter
• MB991928: Engine Hanger
REMOVAL SERVICE POINT
.
<<A>> TRANSAXLE MOUNT BRACKET REMOVAL
1. Install special tools MB991453 and MZ203827 to the vehicle
body to support the engine and transaxle assembly.
2. Install special tools MB991895 and MB991454 to the vehicle
body to support the engine and transaxle assembly.
3. <Engine hanger MB991928 is used>
(1) Assemble the engine hanger (special tool
MB991928).Set following parts the base hanger.
• Slide bracket (HI)
• Foot (standard) (MB991932)
• Foot (short) (MB991933)
• Joint (50) (MB991929)
• Joint (90) (MB991930)
• Joint (140) (MB991931)
(2) Install special tools MB991928 and MB991454 to the
vehicle body to support the engine and transaxle
assembly.
4. Remove the centermember and rear roll stopper bracket.
5. Remove the bolt and nut of the transaxle mount bracket.
6. After lowering the engine and transaxle assembly, remove
the transaxle mount bracket.
ACX00406
MZ203827
AB
MB991453
AC106164
MB991454
MB991895
AB
AC302468
FOOT (SHORT)
(MB991933)
JOINT (90)
(MB991930)
FOOT (STANDARD)
(MB991932)
JOINT (50)
(MB991929)
JOINT (140)
(MB991931)
FRONT
SIDE
SLIDE BRACKET (HI)
AB
AC302400AC
MB991928
SLIDE BRACKET (HI)
MB991454
MB991932
MB991931
MB991933
MB991929
MB991930
TRANSAXLE MOUNTING
TSB Revision
POWER PLANT MOUNT
32-7
INSTALLATION SERVICE POINT
.
>>A<< TRANSAXLE MOUNT STOPPER INSTALLATION
Clamp the transaxle mount stopper so that the arrow points in
the direction as shown in the diagram.
AC000302
ENGINE SIDE
ARROW
TRANSAXLE
MOUNT
BRACKET
AB
TRANS-
AXLE
MOUNT
STOPPER
ENGINE ROLL STOPPER AND CENTERMEMBER
TSB Revision
POWER PLANT MOUNT
32-8
ENGINE ROLL STOPPER AND CENTERMEMBER
REMOVAL AND INSTALLATION
M1321002300135
CAUTION
Mounting locations marked by
*
should be provisionally tightened, and then fully tightened after plac-
ing the vehicle horizontally and loading the full weight of the engine on the vehicle body.
AC000303
45 ± 5 N·m
34 ± 3 ft-lb
45 ± 5 N·m
34 ± 3 ft-lb
45 ± 10 N·m*
34 ± 7 ft-lb*
74 ± 4 N·m
55 ± 3 ft-lb
74 ± 4 N·m
55 ± 3 ft-lb
93 ± 15 N·m
69 ± 11 ft-lb
45 ± 5 N·m
34 ± 3 ft-lb
45 ± 5 N·m*
34 ± 3 ft-lb*
45 ± 5 N·m
34 ± 3 ft-lb
45 ± 5 N·m
34 ± 3 ft-lb
45 ± 10 N·m*
34 ± 7 ft-lb*
93 ± 15 N·m
69 ± 11 ft-lb
74 ± 4 N·m
55 ± 3 ft-lb
45 ± 5 N·m*
34 ± 3 ft-lb*
<3.0L ENGINE>
<2.4L ENGINE>
1
2
2
3
4
5
6
7
8
3
9
10
10
9
1
5
4
8
7
6
3
2
2
2
N
N
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст