Mitsubishi Eclipse. Manual — part 226
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-397
STEP 3. Check the injector.
(1) Disconnect the injector connector B-01 <No. 1 cylinder>,
B-02 <No. 2 cylinder>, B-05 <No. 3 cylinder>, B-06 <No. 4
cylinder>.
(2) Measure the resistance between injector side connector
terminal No. 1 and No. 2.
Standard value: 13
− 16 ohms [at 20°C (68°F)]
Q: Is the resistance between 13 and 16 ohms?
YES : Go to Step 4.
NO : Replace the injector. Then go to Step 9.
STEP 4. Check connector at injector for damage.
a. Check the connector B-01 when checking No. 1 cylinder.
b. Check the connector B-02 when checking No. 2 cylinder.
c. Check the connector B-05 when checking No. 3 cylinder.
d. Check the connector B-06 when checking No. 4 cylinder.
Q: Is the connector in good condition?
YES : Go to Step 5.
NO : Repair or replace the injector. Refer to GROUP 00E,
Harness Connector Inspection
. Then go to
Step 9.
AK300737
1
2
CONNECTORS: B-01, B-02, B-05, B-06
AB
B-02 (GR)
B-01 (GR)
B-05 (GR)
B-06 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AK000559
2
1
INJECTOR SIDE
CONNECTOR
AB
AK300737
1
2
CONNECTORS: B-01, B-02, B-05, B-06
AB
B-02 (GR)
B-01 (GR)
B-05 (GR)
B-06 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-398
STEP 5. Check connector C-49 at ECM <M/T> or connector
C-50 at PCM <A/T> for damage.
Q: Is the connector in good condition?
YES : Go to Step 6.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 9.
AK300413
1
14
4
19
5
22
6
17
8
15
9
18
7
20
16
2
21
23
26
24
25
3
10
11
12
13
CONNECTOR: C-49 <M/T>
C-49 (G)
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AK300414
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
30
21
22
23
24
25
26
27
28
29
31
32
33
34
35
1
10
C-50 (GR)
CONNECTOR: C-50 <A/T>
AB
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-399
STEP 6. Check for harness damage between injector
connector and ECM connector <M/T> or PCM connector
<A/T>.
a. Check the harness wire between injector connector B-01
(terminal No. 2) and ECM connector C-49 (terminal No. 1)
<M/T> or PCM connector C-50 (terminal No. 1) <A/T> when
checking No. 1 cylinder.
b. Check the harness wire between injector connector B-02
(terminal No. 2) and ECM connector C-49 (terminal No. 14)
<M/T> or PCM connector C-50 (terminal No. 9) <A/T> when
checking No. 2 cylinder.
c. Check the harness wire between injector connector B-05
(terminal No. 2) and ECM connector C-49 (terminal No. 2)
<M/T> or PCM connector C-50 (terminal No. 24) <A/T>
when checking No. 3 cylinder.
d. Check the harness wire between injector connector B-06
(terminal No. 2) and ECM connector C-49 (terminal No. 15)
<M/T> or PCM connector C-50 (terminal No. 2) <A/T> when
checking No. 4 cylinder.
Q: Is the harness wire in good condition?
YES : Go to Step 7.
NO : Repair it. Then go to Step 9.
STEP 7. Check the compression.
Refer to GROUP 11A, On-Vehicle Service
− Compression
Pressure Check
Q: Are there any abnormalities?
YES : Go to Step 8.
NO : Repair or replace it. Then go to Step 9.
AK300737
1
2
CONNECTORS: B-01, B-02, B-05, B-06
AB
B-02 (GR)
B-01 (GR)
B-05 (GR)
B-06 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
AK300413
1
14
4
19
5
22
6
17
8
15
9
18
7
20
16
2
21
23
26
24
25
3
10
11
12
13
CONNECTOR: C-49 <M/T>
C-49 (G)
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AK300414
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
30
21
22
23
24
25
26
27
28
29
31
32
33
34
35
1
10
C-50 (GR)
CONNECTOR: C-50 <A/T>
AB
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-400
STEP 8. Replace the injector.
(1) Replace the injector.
(2) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
Other Monitor
(3) Check the diagnostic trouble code (DTC).
Q: Are DTC P0301, P0302, P0303 and P0304 set?
YES : Replace the ECM or PCM. Then go to Step 9.
NO : The inspection is complete.
STEP 9. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to,
Procedure 6
− Other Monitor
.
(2) Check the diagnostic trouble code (DTC).
Q: Are DTC P0301, P0302, P0303 and P0304 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
AK300737
1
2
CONNECTORS: B-01, B-02, B-05, B-06
AB
B-02 (GR)
B-01 (GR)
B-05 (GR)
B-06 (GR)
HARNESS CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст