Mitsubishi Eclipse. Manual — part 121
OIL PAN
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-33
.
>>B<< LOWER OIL PAN INSTALLATION
Tighten the lower oil pan mounting bolts in the order shown.
.
>>C<< DRAIN PLUG GASKET INSTALLATION
Replace the gasket with a new gasket. Install the new gasket in
the direction shown in the illustration.
OIL PAN INSPECTION
M1112002900135
• Check the oil pan for cracks.
• Check the oil pan sealant-coated surface for damage and
deformation.
AC001727
1
2
3
4
5
6
7
8
9
10
AB
ACX00364
DRAIN PLUG
GASKET
OIL PAN
SIDE
AB
CRANKSHAFT FRONT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-34
CRANKSHAFT FRONT OIL SEAL
REMOVAL AND INSTALLATION
M1112003400285
Required Special Tool:
• MD998717: Crankshaft Front Oil Seal Installer
INSTALLATION SERVICE POINTS
.
>>A<< CRANKSHAFT FRONT OIL SEAL INSTALLATION
1. Apply a small amount of engine oil to the oil seal lip and then
insert.
2. Using special tool MD998717, tap the oil seal into the front
case.
Pre-removal and Post-installation Operation
Timing Belt Removal and Installation (Refer to
AC001728AB
8.8 ± 1.0 N·m
78 ± 9 in-lb
1
2
3
4
5
6
6
ENGINE OIL
N
REMOVAL STEPS
>>B<<
1.
CRANKSHAFT SPROCKET
2.
CRANKSHAFT POSITION
SENSOR
>>B<<
3.
CRANKSHAFT SENSING
BLADE
>>B<<
4.
CRANKSHAFT SPACER
5.
KEY
>>A<<
6.
CRANKSHAFT FRONT OIL
SEAL
REMOVAL STEPS (Continued)
ACX00363AB
OIL SEAL
MD998717
CRANKSHAFT
MD998717
CRANKSHAFT REAR OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-35
.
>>B<< CRANKSHAFT SPACER/CRANKSHAFT SENSING
BLADE/CRANKSHAFT SPROCKET INSTALLATION
To prevent the crankshaft pulley mounting bolt from loosening,
degrees or clean the crankshaft, the crankshaft spacer, the
crankshaft sensing blade and the crankshaft at the shown posi-
tions.
CRANKSHAFT REAR OIL SEAL
REMOVAL AND INSTALLATION
M1112003700435
Required Special Tools:
• MD998718: Crankshaft Rear Oil Seal Installer
• MD998781: Flywheel Stopper
ACX01536AB
CRANKSHAFT
CRANKSHAFT
SPACER
CRANKSHAFT
SENSING BLADE
CRANKSHAFT
SPROCKET
SHADED PART : DEGREASE
CLEANING
AC001730
74 ± 2 N·m
55 ± 1 ft-lb
74 ± 2 N·m
55 ± 1 ft-lb
1
2
3
5
2
4
<A/T>
<M/T>
5
ENGINE OIL
AB
REMOVAL STEPS
<<A>>
•
TRANSAXLE ASSEMBLY
•
CLUTCH COVER AND CLUTCH
DISC <M/T> (REFER TO
GROUP 21B, CLUTCH
<<B>>
>>B<<
1.
PLATE <M/T>
<<B>>
>>B<<
2.
ADAPTER PLATE
<<B>>
>>B<<
3.
FLYWHEEL <M/T>
<<B>>
>>B<<
4.
DRIVE PLATE <A/T>
>>A<<
5.
CRANKSHAFT REAR OIL SEAL
REMOVAL STEPS (Continued)
CRANKSHAFT REAR OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-36
REMOVAL SERVICE POINTS
.
<<A>> TRANSAXLE ASSEMBLY REMOVAL
CAUTION
Do not remove the flywheel mounting bolt shown by the
arrow. If this bolt is removed, the flywheel will become out
of balance and damaged.
<M/T>: Refer to GROUP 22A, Transaxle Assembly
<A/T>: Refer to GROUP 23A, Transaxle Assembly
.
.
<<B>> PLATE <M/T>/ADAPTER PLATE/FLYWHEEL
<M/T>/DRIVE PLATE <A/T> REMOVAL
Use special tool MD998781 to secure the flywheel or drive
plate, and remove the bolts.
INSTALLATION SERVICE POINTS
.
>>A<< CRANKSHAFT REAR OIL SEAL INSTALLATION
1. Apply a small amount of engine oil to the entire
circumference of the oil seal lip.
2. Use special tool MD998718 to tap in the oil seal as shown in
the illustration.
.
AC000126
FLYWHEEL
BOLT
AB
<M/T>
ACX00296AB
MD998781
ACX00356AB
MD998718
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст