Mitsubishi Galant. Manual — part 555
HOOD
TSB Revision
BODY
42-3
.
H O O D
BODY DIAGNOSIS
INTRODUCTION TO HOOD DIAGNOSIS
M1421005800136
Wind noise at the hood may be caused by improper
hood adjustment.
HOOD DIAGNOSTIC TROUBLESHOOTING STRATEGY
M1421005900111
Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will be sure that you
have exhausted most of the possible ways to find a
hood fault.
1. Gather information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find the malfunction by following the Symptom
Chart.
4. Verify malfunction is eliminated.
SYMPTOM CHART
M1421006000092
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Difficult locking and unlocking
DIAGNOSIS
STEP 1. Check the release cable routing
condition.
Q: Is the release cable routing condition good?
YES :
Go to Step 2.
NO :
Repair it, then go to Step 4.
STEP 2. Check the engagement of the hood latch
and hood striker.
Q: Are the hood latch and hood striker engaged
correctly?
YES :
Go to Step 3.
NO :
STEP 3. Check for proper lubrication of release
cable.
Q: Is the release cable properly lubricated?
YES :
Go to Step 4.
NO :
Lubricate, then go to Step 4.
STEP 4. Check symptoms.
Q: Does the hood lock operate easily?
YES :
This diagnosis is complete.
NO :
Return to Step 1.
SYMPTOMS
INSPECTION
PROCEDURE
REFERENCE PAGE
Difficult locking and unlocking
1
Uneven body clearance
2
Uneven height
3
HOOD
TSB Revision
BODY
42-4
INSPECTION PROCEDURE 2: Uneven body clearance
DIAGNOSIS
STEP 1. Check the hood installation condition.
Q: Is the hood installation in good condition?
YES :
Go to Step 2.
NO :
STEP 2. Check symptoms.
Q: Is the clearance with the body even?
YES :
This diagnosis is complete.
NO :
Return to Step 1.
INSPECTION PROCEDURE 3: Uneven height
DIAGNOSIS
STEP 1. Check the hood bumper height.
Q: Is the hood bumper height proper?
YES :
Go to Step 2.
NO :
STEP 2. Check symptoms.
Q: Are the hood and body height even?
YES :
This diagnosis is complete.
NO :
Return to Step 1.
HOOD
TSB Revision
BODY
42-5
HOOD
REMOVAL AND INSTALLATION
M1421001600077
AC000554
00007912
18I0310
18I0302
18I0318
18I0310
18C0021
18I0355
18I0300
8
10
10
2
16
16
10
ADJUSTMENT OF HOOD INSTALLATION AND BUMPER
ADJUSTMENT OF HOOD LATCH AND
HOOD STRIKER ENGAGEMENT
<WHEN REPLACING
THE HOOD>
<WHEN REPLACING
THE HOOD AND THE
HOOD HINGE>
FRONT VIEW
REAR VIEW
5
13
15
12 N·m
106 in-lb
12 N·m
106 in-lb
5 N·m
44 in-lb
5 N·m
44 in-lb
22 N·m
16 ft-lb
16
8
4
1
7
11
6
10
12
3
2
9
AB
2
1. HOOD DAMPER
>>A<<
2. HOOD BUMPER A
>>A<<
3. HOOD BUMPER B
4. HOOD WEATHERSTRIP
5. FRONT HOOD WEATHERSTRIP
6. HOOD SWITCH <VEHICLES WITH
THEFT-ALARM SYSTEM>
7. HOOD SUPPORT ROD
8. HOOD LOCK RELEASE HANDLE
HOOD LATCH REMOVAL STEPS
<<A>>
9. RADIATOR GRILLE
10. HOOD LATCH
HOOD LOCK RELEASE CABLE RE-
MOVAL STEPS
•
SPLASH SHIELD (REFER TO
8. HOOD LOCK RELEASE HANDLE
<<A>>
9. RADIATOR GRILLE
10. HOOD LATCH
11. HOOD LOCK RELEASE CABLE
HOOD
TSB Revision
BODY
42-6
REMOVAL SERVICE POINT
<<A>> RADIATOR GRILLE REMOVAL
Remove the radiator grille by pushing all tabs of the radiator
grille clips in the direction of the arrows with a flat-tipped
screwdriver, then lightly pull the radiator grille toward you.
INSTALLATION SERVICE POINT
>>A<< BUMPER B/BUMPER A INSTALLATION
Install bumpers A and B as shown in the illustration.
Be sure they are adjusted so the hood is even with the body on
all sides.
INSPECTION
M1421001700063
HOOD SWITCH CONTINUITY CHECK <VEHICLES WITH
THEFT-ALARM SYSTEM>
HOOD INSULATOR REMOVAL STEPS
12. CLIP
13. HOOD INSULATOR
HOOD AND HOOD HINGE REMOVAL
STEPS
14. WASHER HOSE CONNECTION
15. HOOD
•
FRONT DECK GARNISH (REFER
TO GROUP 51, WINDSHIELD
WIPER AND WASHER
16. HOOD HINGE
AC000555AB
AC000556
BUMPER A
BUMPER B
18.3 – 19.3 mm
(0.72 – 0.76 in)
15.5 – 16.5 mm
(0.61 – 0.65 in)
AB
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
Hood switch
unpressed
1
−
2
Continuity
Hood switch
depressed
-
No Continuity
AC000557
00010395
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст