Mitsubishi Galant. Manual — part 79
ON-VEHICLE SERVICE
TSB Revision
ENGINE LUBRICATION
12-5
4. Use the respective tool in the following table to remove the
engine oil filter.
5. Clean the filter bracket side mounting surface and ensure
the old O-ring has been removed.
6. Apply a small amount of engine oil to the O-ring of the new
oil filter.
7. Once the O-ring of the oil filter is touching the flange, use the
respective tool in the following table to tighten to the
specified torque.
8. Install the drain plug and refill engine oil. (Refer to Engine
Oil Replacement
9. Race the engine a few times, and check to be sure that no
engine oil leaks from the installation section of the oil filter.
AC000093 AC
MB991396,
MB991610 OR
GENERAL
SERVICE
TOOL
ACX00396
O-RING
AB
NUMBER
ENGINE
SPECIAL TOOL
TIGHTENING TORQUE
MD360935
2.4L
MB991396 or equivalent
Approximately one turn [14 N
⋅
m (124 in-lb)]
MD325714,
MD332687,
MD365876
MB991396 or equivalent
Approximately 3/4 turn [16 N
⋅
m (11.6 ft-lb)]
MD136466,
MD322508
General service tool
Approximately 3/4 turn [17 N
⋅
m (12.5 ft-lb)]
MD352626
3.0L
MB991610 or equivalent
Approximately 3/4 turn [14 N
⋅
m (124 in-lb)]
ON-VEHICLE SERVICE
TSB Revision
ENGINE LUBRICATION
12-6
OIL PRESSURE CHECK
M1121002300078
Required Special Tool:
MD998054:Oil Pressure Switch Wrench
1. Check engine oil quantity.
2. Remove the oil pressure switch terminal.
CAUTION
Since sealant is applied to the thread of the oil pressure
switch, take care not to damage the oil pressure switch
when removing it.
3. Use special tool MD998054 to remove the oil pressure
switch.
4. Install the oil pressure gauge.
NOTE: Use a 1/8 pipe thread adapter.
5. Run the engine to warm it.
6. After the engine has been warmed up, check that oil
pressure is within the standard value.
Standard value:
At idle: 29 kPa (4.2 psi) or more
At 3,500 r/min: 294
−−−−
686 kPa (43
−−−−
100 psi)
7. Remove the oil pressure gauge.
8. Apply the specified sealant 3M
AAD Part number 8672 or
equivalent to thread of the oil pressure switch.
AK000197AB
CYLINDER BLOCK
OIL PRESSURE
SWITCH
<2.4L ENGINE>
AKX00293
CYLINDER BLOCK
OIL FILTER
BRACKET
OIL PRESSURE
SWITCH
AKX00293AC
<3.0L ENGINE>
AKX00294
MD998054
AB
AKX00295 AB
SPECIFICATIONS
TSB Revision
ENGINE LUBRICATION
12-7
CAUTION
Do not start the engine within one hour after the engine oil
pressure switch has been installed.
9. Use special tool MD998054 to tighten the oil pressure switch
to the specified torque.
Tightening torque:
19 N
⋅⋅⋅⋅
m (14 ft-lb) <2.4L ENGINE>
9.8 N
⋅⋅⋅⋅
m (87 in-lb) <3.0L ENGINE>
10.Install the oil pressure switch terminal.
SPECIFIC ATIO NS
FASTENER TIGHTENING SPECIFICATIONS
M1121002200060
SERVICE SPECIFICATION
M1121000300027
SEALANT
M1121000500021
LUBRICANTS
M1121000400080
AKX00294
MD998054
AB
ITEMS
SPECIFICATIONS
Engine oil filter
MD360935, MD352626
14 N
⋅
m (124 in-lb)
MD325714, MD332687,
MD365876
16 N
⋅
m (11.6 ft-lb)
MD136466, MD322508
17 N
⋅
m (12.5 ft-lb)
Engine oil pan grain plug
39 N
⋅
m (29 ft-lb))
Oil pressure switch
2.4L Engine
19 N
⋅
m (14 ft-lb)
3.0L Engine9.8 N
⋅
m (87 in-lb)
ITEM
STANDARD VALUE
Oil pressure kPa (psi)
at idle
29 (4.2) or more
at 3,500 r/min
294
−
686 (43
−
100)
ITEM
SPECIFIED SEALANT
Oil pressure switch
3M
AAD Part No. 8672 or equivalent
ITEMS
ENGINE OIL (API CLASSIFICATION)
QUANTITY dm
3
(qt)
Oil filter
SJ or higher
0.3 (0.32)
Total quantity
4.3 (4.5)
SPECIFICATIONS
TSB Revision
ENGINE LUBRICATION
12-8
ENGINE OIL
CAUTION
Never use nondetergent or straight mineral oil.
Oil Identification Symbol
Use only engine oils displaying the ILSAC certification mark
("Starburst" symbol) on the container.
If these oils are not available, an API classification SJ EC or SJ/
CD EC can be used.
ACX00394AI
ILSAC CERTIFICATION MARK
("STARBURST" SYMBOL)
ACX00886 AB
API SERVICE SYMBOL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст