Mitsubishi Galant. Manual — part 78
12-1
GROUP 12
CONTENTS
GENERAL INFORMATION . . . . . . . .
SPECIAL TOOLS. . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE. . . . . . . . . . .
ENGINE OIL CHECK . . . . . . . . . . . . . . . . .
ENGINE OIL REPLACEMENT . . . . . . . . . .
ENGINE OIL FILTER REPLACEMENT . . .
OIL PRESSURE CHECK . . . . . . . . . . . . . .
SPECIFICATIONS . . . . . . . . . . . . . . .
FASTENER TIGHTENING SPECIFICATIONS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATION . . . . . . . . . . . .
SEALANT . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL INFORMATION
TSB Revision
ENGINE LUBRICATION
12-2
.
G EN ER A L IN FO R M ATIO N
M1121000100090
The lubrication method is a fully force-fed, full-flow
filtration type.
ENGINE OILS
WARNING
Prolonged, repeated contact with mineral oil will result in the removal of natural fats from the
skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains
potentially harmful contaminants which may cause skin cancer. Adequate means of skin
protection and washing facilities must be provided.
Recommended Precautions
The most effective precaution is to adapt working
practices which prevent, as far as practicable, the
risk of skin contact with mineral oils. For example;
Use enclosed systems for handling used engine oil
and decrease components, where practicable,
before handling them.
Other precautions:
•
Avoid prolonged and repeated contact with oils,
particularly used engine oils.
•
Wear protective clothing, including impervious
gloves where practicable.
•
Avoid contaminating clothes with oil.
•
Do not put oily rags in pockets.
•
Do not wear heavily soiled clothing and oil-
impregnated foot wear. Work clothing must be
cleaned regularly and kept separate from
personal clothing.
•
Where there is a risk of eye contact, eye
protection should be worn. For example;
chemical goggles or face shields. In addition, an
eye wash facility should be provided.
•
Obtain First Aid treatment immediately for open
cuts and wounds.
•
Wash regularly with soap and water to ensure all
oil is removed, especially before meals (skin
cleansers and nail brushes will help). After
cleaning, the application of preparations
containing lanolin to replace the natural skin oils
is advised.
•
Do not use gasoline, kerosene, diesel fuel, gas
oil, thinners or solvents for cleaning skin.
•
Use barrier creams, applying them before each
work period, to help the removal of oil from the
skin after work.
•
If skin disorders develop, obtain medical advice
immediately.
ITEMS
2.4L ENGINE
3.0L ENGINE
Oil pump type
Involute gear type
Trochoid type
Drive method
Timing belt
Crankshaft
SPECIAL TOOLS
TSB Revision
ENGINE LUBRICATION
12-3
SPECIA L TO O LS
M1121000600084
O N -VEH IC LE SERVIC E
ENGINE OIL CHECK
M1121000900063
1. Pull out the oil dipstick slowly and check that the oil level is
within the marks on the oil dipstick.
2. Check that the oil is not excessively dirty, that there is no
coolant or gasoline mixed in, and that it has sufficient
viscosity.
ENGINE OIL REPLACEMENT
M1121001000074
1. Start the engine and allow it to warm up until the
temperature of the coolant reaches 80
°
C (176
°
F
)
to
90°
C
(194
°
F).
2. Remove the engine oil filler cap.
WARNING
Use care as oil could be hot.
3. Remove the drain plug to drain oil.
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB991396
Oil filter wrench
−
Removal and installation of
engine oil filter (when using
the oil filter of MD360935,
MD325714, MD332687 and
MD365876) <2.4L Engine>
MB991610
Oil filter wrench
−
Removal and installation of
engine oil filter (when using
the oil filter of MD352626)
<3.0L Engine>
MD998054
Oil pressure switch
wrench
−
Removal and installation of
oil pressure switch
B991396
MB991610
ON-VEHICLE SERVICE
TSB Revision
ENGINE LUBRICATION
12-4
4. Install a new drain plug gasket so that it faces in the
direction shown in the illustration, and then tighten the drain
plug to the specified torque.
Tightening torque: 39 N
⋅⋅⋅⋅
m (29 ft-lb)
5. Refill the specified quantity of oil.
Specified Engine Oil (API classification): SJ or higher
Total quantity (Includes volume inside oil filter): 4.3
dm
3
(4.5 quarts)
6. Install the engine oil filler cap.
7. Check oil level.
ENGINE OIL FILTER REPLACEMENT
M1121001100071
Required Special Tools:
•
MB991396 (When using the oil filter of MD360935,
MD325717, MD332687 and MD365876): Oil Filter Wrench
•
MB991610 (When using the oil filter of MD135737):
Oil Filter Wrench
1. Start the engine and allow it to warm up until the
temperature of the coolant reaches 80
°
C (176
°
F) to
90°
C
(194
°
F).
2. Remove the engine oil filler cap.
WARNING
Use care as oil could be hot.
3. Remove the drain plug to drain oil.
AC000092
<2.4L ENGINE>
DRAIN PLUG GASKET
OIL
PAN
SIDE
DRAIN
PLUG
39 N·m
29 ft-lb
39 N·m
29 ft-lb
DRAIN
PLUG
OIL
PAN
SIDE
DRAIN PLUG GASKET
<3.0L ENGINE>
AC
ACX00887AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст