Mitsubishi Galant. Manual — part 620
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-33
STEP 7. Check the combination meter connector C-29 for
damage.
Q: Is combination meter connector C-29 in good
condition?
YES : Go to Step 8.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The speedometer
should work normally.
STEP 8. Check the harness wire between combination
meter connector C-29 and ground.
Q: Is the harness wire between combination meter
connector C-29 and ground in good condition?
YES : There is no action to be taken.
NO : Repair it. The speedometer should work normally.
AC003089 AD
CONNECTOR: C-29
AC003089 AD
CONNECTOR: C-29
TSB Revision
CHASSIS ELECTRICAL
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
54A-34
STEP 9. Check the combination meter vehicle speed
sensor input signal circuit at the combination meter
connector C-30.
(1) Disconnect the vehicle speed sensor connector B-35.
(2) Disconnect the combination meter connector C-30.
(3) Turn the ignition switch to "ON" position.
(4) Measure the voltage between terminal 16 and ground.
Q: Is the voltage approximately 5 volts?
YES : Repair or repair the combination meter (printed-
circuit board or speedometer and tachometer). The
speedometer should work normally.
NO : Go to Step 10.
STEP 10. Check the combination meter connector C-30 for
damage.
Q: Is combination meter connector C-30 in good
condition?
YES : Go to Step 11.
NO : repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The speedometer
should work normally.
AC003686
CONNECTOR: B-35
<2.4L ENGINE>
AB
AC003687
CONNECTOR: B-35
<3.0L ENGINE>
AB
AC002886AB
CONNECTOR: C-30
(HARNESS SIDE)
AC003089 AH
CONNECTOR: C-30
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-35
STEP 11. Check the harness wires between combination
meter connector C-30 and vehicle speed sensor connector
B-35.
NOTE: After checking intermediate connector C-17, and joint
connector C-56, check the wires. If intermediate connector C-
17 and joint connector C-56 are damaged, repair or replace
them. Refer to GROUP 00E, Harness Connector Inspection
Q: Are the harness wires between combination meter
connector C-30 and vehicle speed sensor connector B-
35 in good condition?
YES : There is no action to be taken.
NO : repair them. The speedometer should work normally.
AC003686
CONNECTOR: B-35
<2.4L ENGINE>
AB
AC003687
CONNECTOR: B-35
<3.0L ENGINE>
AB
AC003089
C-56
CONNECTORS: C-30, C-56
AP
C-30
AC003089 AI
CONNECTOR: C-17
TSB Revision
CHASSIS ELECTRICAL
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
54A-36
STEP 12. Check the vehicle speed sensor power supply
circuit at the vehicle speed meter connector B-35.
(1) Disconnect the vehicle speed sensor connector B-35.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 1 and ground.
Q: Is the voltage approximately 12 volts (battery positive
voltage)?
YES : Go to Step 15.
NO : Go to Step 13.
STEP 13. Check the vehicle speed sensor connector B-35
damage.
Q: Is vehicle speed sensor connector B-35 in good
condition?
YES : Go to Step 14.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The speedometer
should work normally.
AC002750AB
CONNECTOR: B-35
(HARNESS SIDE)
AC003686
CONNECTOR: B-35
<2.4L ENGINE>
AB
AC003687
CONNECTOR: B-35
<3.0L ENGINE>
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст