Mitsubishi Galant. Manual — part 364
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-26
STEP 12. Check the harness wire between auto-cruise
control vacuum pump connector A-01 and auto-cruise
control-ECU connector C-52.
Q: Is any harness wire between auto-cruise control
vacuum pump connector A-01 and auto-cruise control-
ECU connector C-52 damaged?
YES : Repair harness wire and then check that diagnostic
trouble code 14 is not output.
NO : Check that diagnostic trouble code 14 is not output.
If diagnostic trouble code 14 is output, replace the
auto-cruise control-ECU. (Refer to
.)
Then check that diagnostic trouble code 14 is not
output.
STEP 13. Check the output circuit voltage at auto-cruise
control-ECU connector C-52 by backprobing.
(1) Do not disconnect auto-cruise control-ECU connector C-52.
(2) Turn the ignition switch to "ON" position and the auto-cruise
control main switch to "ON" position.
(3) Measure the voltage between terminal 5 and ground by
backprobing.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage approximately battery positive voltage?
YES : Go to Step 14.
NO : Go to Step 15.
AC001449
CONNECTOR: A-01
RESERVE
TANK
AB
AC004572AB
CONNECTOR: C-52
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
ACX01899
C-52 CONNECTOR
HARNESS SIDE VIEW
AD
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-27
STEP 14. Check intermediate connector C-05.
Q: Is any connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that diagnostic trouble code 14 is not
output.
NO : Check the harness wire between auto-cruise control-
ECU connector C-52 and stoplight switch connector
C-03 for open circuit or damage.
Then repair if necessary.
Then check that diagnostic trouble code 14 is not
output.
STEP 15. Check auto-cruise control-ECU connector C-52.
Q: Is the connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector
Inspection
Then check that diagnostic trouble code 14 is not
output.
NO : Check that diagnostic trouble code 14 is not output.
If diagnostic trouble code 14 is output, replace the
auto-cruise control-ECU. (Refer to
.)
Then check that diagnostic trouble code 14 is not
output.
AC004571
CONNECTOR: C-05
COMBINATION METER
AB
AC004572AB
CONNECTOR: C-52
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-28
DTC15 : Auto-cruise Control Switch System
CIRCUIT OPERATION
This circuit judges the signals of each switch ("OFF,"
"SET," "RESUME," "CANCEL" and "MAIN") of the
auto-cruise control switch.
The auto-cruise control-ECU detects the state of the
auto-cruise control switch by sensing the voltages
shown below.
AC004582
Auto-cruise Control Switch System Circuit
AB
AC004572AB
CONNECTOR: C-52
AC004583AB
C-64
C-61
CONNECTORS: C-61, C-64
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-29
•
When all switches are OFF, the ECU detects 3.5
−
5.0 volts.
•
When the "SET" switch is ON, the ECU detects
0.4
−
2.3 volts.
•
When the "RESUME" switch is ON, the ECU
detects 2.3
−
3.5 volts.
•
When the "CANCEL" switch is ON, the ECU
detects 0.4 volts or less.
•
When the main switch is ON, the ECU detects
7.0 volts.
DTC SET CONDITIONS
This code is output when the auto-cruise control
switch "RESUME" switch, "SET" switch or
"CANCEL" switch stays ON.
TROUBLESHOOTING HINTS
The most likely causes for this code to be set are:
•
Malfunction of the auto-cruise control switch.
•
Malfunction of the clock spring.
•
Damaged harness or connector.
•
Malfunction of the auto-cruise control-ECU
DIAGNOSIS
Required Special Tool:
•
MB991223: Harness Set
STEP 1. Check the 12-Volt supply circuit voltage at auto-
cruise control switch connector C-64.
(1) Disconnect auto-cruise control switch connector C-64 and
measure at the harness side.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 1 and ground.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage approximately battery positive voltage?
YES : Go to Step 5.
NO : Go to Step 2.
STEP 2. Check auto-cruise control switch connector C-64.
Q: Is the connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that diagnostic trouble code 15 is not
output.
NO : Go to Step 3.
1
2
3
ACX02255AD
AUTO-CRUISE
CONTROL SWITCH
CONNECTOR: C-64
AC004584
CONNECTOR: C-64
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст