Mitsubishi Galant 9G. Manual — part 1134
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-836
DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991910: Main Harness A
STEP 1. Check fuel gauge.
Q: Is the fuel gauge functioning?
YES : Go to Step 2.
NO : Refer to GROUP 54A, Chassis Electrical
−
Combination Meters Assembly and Vehicle Speed
Sensor
− Equipment Diagnosis − Symptom Chart
STEP 2. Check harness connector B-20 at PCM and
harness connector D-17 at fuel level sensor (sub) for
damage.
Q: Is the harness connector in good condition?
YES : Go to Step 3.
NO : Repair or replace them. Refer to GROUP 00E,
Harness Connector Inspection
Then go to
Step 7.
AK303878
1
2
AB
CONNECTOR: D-17
D-17
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-837
STEP 3. Check for short circuit to ground between PCM
connector B-20 (terminal No. 24) and fuel level sensor
(sub) connector D-17 (terminal No. 1).
NOTE: Check harness after checking intermediate connectors
C-25. If intermediate connectors are damaged, repair or
replace them. Refer to GROUP 00E, Harness Connector
Inspection
. Then go to Step 7.
Q: Is the harness wire in good condition?
YES : Go to Step 4.
NO : Repair it. Then go to Step 7.
AK303878
1
2
AB
CONNECTOR: D-17
D-17
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303092
25
21
24 23 22
29 28 27 26
34 33 32 31 30
38 37 36 35
43 42 41 40 39
CONNECTOR: B-20
B-20
PCM
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AIR CLEANER
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-838
STEP 4. Check harness connector D-18 at fuel level sensor
(main) for damage.
Q: Is the harness connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Then go to Step 7.
STEP 5. Check for short circuit to ground between fuel
level sensor (main) connector D-18 (terminal No. 2) and
fuel level sensor (sub) connector D-17 (terminal No. 1).
Q: Is the harness wire in good condition?
YES : Go to Step 6.
NO : Repair it. Then go to Step 7.
AK303840
1
2
3
4
5
SERVICE
HOLE
AB
CONNECTOR: D-18
D-18 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303878
1
2
AB
CONNECTOR: D-17
D-17
HARNESS
CONNECTOR:
COMPONENT SIDE
AK303840
1
2
3
4
5
SERVICE
HOLE
AB
CONNECTOR: D-18
D-18 (GR)
HARNESS
CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.8L ENGINE>
13B-839
STEP 6. Check the trouble symptoms.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0461 set?
YES : Replace the PCM. Then go to Step 7.
NO : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunctions
.
STEP 7. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to
Diagnostic Function
− OBD-II Drive Cycle − Procedure 6 −
(2) Check the diagnostic trouble code (DTC).
Q: Is DTC P0462 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст